Broken pins preventing PC from starting?

Help (General)

Parts:

  • CPU: Borked Ryzen 5 5600X
  • PSU: Corsair SF750
  • MB: Gigabyte Aorus X570SI Pro Ax rev 1.1 (Q-Flashed to F3 BIOS prior to CPU installation)
  • RAM: T-Force DARK Zα DDR4 3600Mhz 2x16GB (should be on the QVL)
  • GPU: MSI GeForce RTX 2070 Super Ventus OC (using an HDMI 2.0? cable right now)
  • SSD/HDD: 2TB WD SN770 Gen 4.0 NVMe & spare 2.5" HDD
  • Case: CoolerMaster NR200P
  • Cooler: CoolerMaster Hyper 212 Black w/ MasterGel paste (did 1 drop on the CPU IHS)
  • Case Fans: 2x CM Sickleflow 120mm (top exhaust), 2x Arctic P12 Slim 120mm (bottom intake)

Original problem:

TL;DR: Would 3 VSS and the MB_DQS_L[5] pin being snapped off a R5 5600X (bottom right corner, if the gold arrow is facing the top left) - prevent my PC from turning on at all? How can I be sure it's the CPU and not some other component, say the motherboard? Surely there should be some sign of life?

Crucially, the mobo does supply power to peripherals connected to the rear and front I/O, which is the only thing that does work. Having said that, no case nor CPU fans spin up, no integrated speaker nor any diagnostic LEDs on this model of mobo, so I'm deaf and blind there, and GPU also doesn't spin up, so no display at all.

Troubleshooting:

  • I've gone through most of Tom's Hardware troubleshooting checklist, specifically:
  • Front header pwr/reset/LED lead positions were double checked
  • RAM (that's on the mobo QVL) was reseated and tested in single / no stick configs
  • SSD/HDD reseated and also tried to boot without them
  • 8-pin EPS & 24-pin ATX cables seated properly with the right cables in the right slots on my PSU (as far as I can tell)
  • GPU connected with 6+2 and 6-pin PCIe Y-cable terminating to a single 8-pin slot on the PSU
  • BIOS flashed to the latest version prior to doing anything
  • no loose wires, screws or thermal paste on the mobo, no ESD-strap but very careful whilst building in a slightly humdified room on a non-conductive surface, GPU double checked for seating but also tested boot without it

The only other thing I can think of is that the mobo does have a backplate heatsink that may be making contact with the case, causing a short? Still, that sounds like such a dumb oversight by the mobo manufacturer (and I'm only using the standoffs that were preinstalled by the case manufacturer, nothing else should be underneath it).

If anyone's wondering how I borked the CPU pins: well, they may have been damaged in transit, or due to my own panic. Whilst installing the CPU cooler, I didn't realize how much force you needed for the Hyper 212's mounting screws, and the CPU was lifting up at one corner as I was threading one screw, so I stopped halfway through the installation and welp, ripped the CPU right out of the socket whilst removing the cooler. You'll forgive me for not doing the twist and slide method as I haven't built a PC in a decade and didn't know AM4's retention arm did squat at holding CPUs in place.

So, I tried bending the pins back, but did a hack job of it and 4 came off. And yes the CPU was aligned to the gold arrow and the retention arm was lifted and closed respectively prior to and after installing it.

Would appreciate any insights 🙏

https://imgur.com/a/DXqCEI6 reference images attached

Posted Jan 11, 2023, 4:12 AM UTC · edited

13
tattoedblues5600X/6700XT•

It’s the CPU, sorry man

1
Obvious_Drive_1506•

Yes it would prevent it from turning on. Your cpu is dead.

1
Melodias3•

If i had broken legs i probably not be able to walk, if you have broken pins and an issue with PC its probably cos of broken pins, don't waste energy into this either try fix it or buy new cpu.

Some pins are for data or other stuff and then you have grounding pin, you could have 1 pin broken that is responsible for example for 1 of your ram slots for example that you don't use and end up lucky but usually no one is this lucky, see if you can get it repaired or replace it.

1