A "first draft" of some leather working knives I made.

The Tools I use
A "first draft" of some leather working knives I made.

Posted Jan 16, 2023, 11:12 PM UTC

32623
randumthingz•

I’ve been a blacksmith for 5 years and a leather worker for 2. How have I never thought of this before?? 🤦🏼‍♀️

15

Second from the right looks like it could be the cutest little butter knife!

7
Bellociraptor•

Agreed. Initially thought I was looking at a totally rad cheese knife set.

4
Keeper_71•

Very nice,

What steel did you use for these? I have been considering making a couple items like this.

5
NeotianOP•

Thank you.

1.2442 and 1.2419.05. These are German specialty alloys so might not be readily available. In general I think any high carbon steel should work, if it's a little bit alloyed for higher wear resistance and stability all the better.

3
Webicons•

Not sure where you’re from but if the local suppliers don’t have the steel I’m looking for (which is rare) then there are some specialty catalog companies like this: https://www.dictum.com/en/steel-cca?p=3

3
Keeper_71•

Thanks, I am in Ontario. But your answer helps.

1
dangb2Small Goods•

Awesome work, this is addicting! I have two custom knives I designed myself. Did a bunch of research on steel types, hardness, angles and geometry... Too bad I had to have them made, would love to actually make one sometime.

3

Flipping wicked!

These looks beautiful.

I have been connecting with knife makers in my community, so I'd love to see if anyone is ever going to be up for making something like this.

I'll save this post for later.

3
sonofloy•

Loving the look of the skiving knives!! Keep us updated on how it’s been working

2
GizatiStudio•

Impressive.

2
vomeronasal•

Those look great! I’ve been planning on making my own, too.

2
McewenHandcraft•

Slick!!! Been planning on making myself some skiving chisels similar to this. But my little tin can forge isn't big enough for more than very small knives. Working on expanding my tools before I make the attempt

2
excitablelizard•

I love the grain, really nice

2

I thought these were cheese knives and got very excited. They’re beautiful, even if they’re not made for cheese!

2
Wretchfromnc•

I’ve made the far left and the one beside it, I’d like the far right with a angled edge instead of being 90 degrees.

2
grewgrewgrewgrew•

the middle ones look left-handed

2
TheGopNikk•

Beautiful 👌👌👌

2
vomeronasal•

What's the thickness on those? Any any design tips for making my own? I've been a knifemaker for 20 years but never made leatherworking knives.

2
NeotianOP•

Thickness is 2,7mm and about 4 mm. Thinner stock and a high bevel make for less resistance when skiving but have to be matched with the right sharpening angle or the edge gets to fragile. For just cutting along lines 4mm with a 3cm bevel seems to be fine. I did some scalpel like knives for just cutting out the shapes in 1,7mm and those work really well but with a high bevel flex quite a bit.

In the next iteration I would probably center the handle because for some operations the handle alignment to one side feels a bit unnatural. This could be countered with more specialized knives (one just for skiving and one just for cutting etc.) but having 8 knives or so on the table is not all that practical.

I will experiment with a hollow ground back for ease of sharpening because grinding the back on wear resistant steel is a bit of a pain.

Some thoughts of the top of my head but they probably can be iterated quite well if I had the time to make some more.

2
vomeronasal•

Thanks!

2
austing3115•

Second from the right is beautiful

2
DarthNervous_•

Truly excellent!!!

2