Strange Problems after installing Creality Sprite pro and additional Z axis screw & stepper motor.

I recently upgraded my Ender 3v2 with a Sprite Pro hot end and Dual Z axis upgrade. I previously had a BL touch installed which functioned without issue. I had no issues printing prior to this but now I am unable to print at all. Issues are listed below.

  • During most of the tests I tried the print head and bed would heat up and then idle there for several minutes. The print head would then cool down and restart the heating process before moving to the left side of the build plate. There the printer will register the print as complete despite not having printed anything.
    • I have a single file on my SD card for this test, a file I’ve used dozens of times to test settings. I use the Hydra Bed Level Test.
  • While attempting to level the bed using the onboard leveling option the printhead will attempt to move beyond the X axis limit where the belt starts to slip. It will do this for about 1-2 seconds, move slightly to the left, and then check one point for before stopping the leveling test.
    • The bed leveling failing is less of a concern compared to the device thinking the X axis is longer than it really is. I imagine this is likely because of the difference in mounting brackets for the stock Ender 3v2 hot end and the Sprite Pro.
    • On another attempt the print head moved as above and then pulled the print bed all the way back to the home position. The printhead then moved down with the sensor nowhere near the print bed let alone any of the points it should be checking. I had to turn the power off at this point to keep the hot end nozzle from diving into the print bed and causing any damage.
  • The device appears to think the print bed is in a different position than it actually is. I managed to get a few test prints to actually start but the print was probably 30-40mm off center to the right.
    • I scaled down the hydra test and adjusted my slicer settings for a more narrow bed but haven't been able to test this out due to the first issue.

Here is what I have done and checked so far:

  • I've checked all connections and ports to make sure they are properly seated and wired correctly.
    • I did not realize initially that I had mixed up the positive and negative wires on my heating tube when plugging them into the board. When I turned the printer on after my initial build and attempted to heat up the hot end the printer just turned off. I figured this out pretty quickly but I am worried I may have shorted something out on my board.
  • I've updated the printer firmware to the most recent version from the Creality website. I made sure to download the one tagged Marlin. I also made sure I matched it with my motherboard (4.2.2.)

TL;DR
Printer alternates between not wanting to start prints at all and when it does it thinks the bed is in a different position relative to the printhead that it actually is.

Posted Mar 26, 2023, 5:07 PM UTC

14
chris24m•

There are a few settings that might need adjusting. You need to set the nozzle offset. Mine is around x = -32 and y= -40. If you installed the new hardware properly, your sprite can travel so the nozzle goes off the bed (to the right if standing in front of the machine). You can measure how far right it can go and set the x_max position to that number. Mine is around 20 extra mm, so 235mm bed + 20mm = 255mm (though my nozzle doesn’t reach the very left of the bed… so mine is about 250mm). You would then do this for the y_max position as well. That should dial in the bed size issue. There are a few other settings that may need changed, such as when you home x, do you want the probe to probe the actual center of the bed, or do you want the nozzle over the center of the bed. If you are using the BL touch to creat meshes, then you have a bed margin offset setting to ensure the probe doesn’t try to probe off the side of the bed.

If you are just using the precompiled firmware settings from Creality, I believe there are ways to adjust these settings in the Marlin menu. I have just always done a custom compile with VS Code, though it can be a bit of a learning curve to compile firmware. There are many YouTube videos that go over that topic very well.

As for the not printing issue, my only guess is that it could be part of the starting gcode that may not be compatible with the all the new settings, but that is purely a guess.

I am still learning a lot about this, as I am currently in the final stages of doing a massive upgrade to my Ender 3 v2. I am no expert but hope this points you in the right direction!

1
Fierce_FoxOP•

Thank you, I'll try and give this is a shot when I get home. I haven't messed with any software and I try not to unless I really need to. It's not something I'm comfortable with and really don't understand. Heck I only recently started messing with the print settings in my slicer UI and I've been printing for a few years now. I'm more of a caveman playing with fire than anything else. Finding explanations for a lot of this stuff that are at my level can be challenging to say the least.

1
chris24m•

If you need any help, feel free to DM me!

1

I also just install a Sprite Direct Drive Extruder. Fortunately for me I installed the head correctly other then plugging in the RED wires for the hot end. Man that took me for ever to figure out. I downloaded the firmware from Creality for the Sprite Extruder. I have a BL Touch as well. My first issue was that the wiring that came with the Sprite did not work correctly with the BL Touch, so I just installed the wiring that came with the BL Touch. Now it works.

I don't understand the x = -32 and y= -40 settings. Is this done in the slicer program? I have spent all last night trying to find out what this means. I could not figure it out at all. I did notice that the Sprite Print head Carriage has a finger to the left of it that prevents it from going all the way to the left of the bed, which offsets the prints to the right. Now I loose printing space to the left of the bed. Is there a way to fix this.

1
allanworks•

the second issue is your trolly is hitting the gantry. you need to replace the upper right and lower bolt with a m5 25mm bolt with a non-locking nut but make sure to use a thread locker. also due to the different positions of the nozzle on the sprite, you lose a little bit of print space unless you do like me and move the glass bed over a few mm to make up for it.

1

This is a Fakespot Reviews Analysis bot. Fakespot detects fake reviews, fake products and unreliable sellers using AI.

Here is the analysis for the Amazon product reviews:

Name: Creality Sprite Direct Drive Extruder Pro Kit, All Metal Extruder Upgrade Kit for Ender 3/Ender 3 v2/Ender 3 Pro/Ender 3 Max 3D Printer,Dual Gear Dual Fan Design,Support BL Touch/CR Touch

Company: Visit the YOOPAI Store

Amazon Product Rating: 4.4

Fakespot Reviews Grade: C

Adjusted Fakespot Rating: 2.5

Analysis Performed at: 02-27-2023

Link to Fakespot Analysis | Check out the Fakespot Chrome Extension!

Fakespot analyzes the reviews authenticity and not the product quality using AI. We look for real reviews that mention product issues such as counterfeits, defects, and bad return policies that fake reviews try to hide from consumers.

We give an A-F letter for trustworthiness of reviews. A = very trustworthy reviews, F = highly untrustworthy reviews. We also provide seller ratings to warn you if the seller can be trusted or not.

0