Ender 5 Pro, BTT SKR Mini E3 V3 w/TFT35, CR Touch, Klipper won't move Z axis up when homing.

Software Help

I just switched to Klipper and right now I'm on day 3 of trying to figure out why my Z axis will not move up when homing. X and Y both home correctly. I've been through numerous forums and YouTube videos with no luck.

If I add the ! in front of the Z axis dir_pin in my printer.cfg, the bed will move down while homing. If I take that out it does nothing. The CR touch tests out properly when running commands.

I can post my printer.cfg in a few minutes in the comments. Can anyone help a brother out?

Posted Mar 31, 2023, 1:08 AM UTC

24
WanHackCertified Expert•

I can take a look, but it'll have to wait till tomorrow

1
CommonInterfaceOP•

[include mainsail.cfg]

[virtual_sdcard]

path: /home/tony/printer_data/gcodes

on_error_gcode: CANCEL_PRINT

​

[bltouch]

sensor_pin: ^PC14

control_pin: PA1

x_offset: -45.5

y_offset: -7.0

samples: 2

speed: 2

z_offset: 3.0

pin_up_touch_mode_reports_triggered: False

probe_with_touch_mode: True

​

[safe_z_home]

home_xy_position: 110,110 # Change coordinates to the center of your print bed

speed: 50

z_hop: 10 # Move up 10mm

z_hop_speed: 5

​

[bed_mesh]

speed: 120

horizontal_move_z: 5

mesh_min: 10, 10

mesh_max: 190, 220

probe_count: 5,5

​

[stepper_x]

step_pin: PB13

dir_pin: !PB12

enable_pin: !PB14

microsteps: 16

rotation_distance: 40

endstop_pin: ^PC0

position_endstop: 235

position_max: 235

homing_speed: 50

​

[tmc2209 stepper_x]

uart_pin: PC11

tx_pin: PC10

uart_address: 0

run_current: 0.580

hold_current: 0.500

stealthchop_threshold: 999999

​

[stepper_y]

step_pin: PB10

dir_pin: !PB2

enable_pin: !PB11

microsteps: 16

rotation_distance: 40

endstop_pin: ^PC1

position_endstop: 235

position_max: 235

homing_speed: 50

​

[tmc2209 stepper_y]

uart_pin: PC11

tx_pin: PC10

uart_address: 2

run_current: 0.580

hold_current: 0.500

stealthchop_threshold: 999999

​

[stepper_z]

step_pin: PB0

dir_pin: !PC5

enable_pin: PB1

microsteps: 16

rotation_distance: 8

endstop_pin: probe:z_virtual_endstop

# endstop_pin: ^PC2

# position_endstop: 0.0

position_max: 250

position_min: -2

​

[tmc2209 stepper_z]

uart_pin: PC11

tx_pin: PC10

uart_address: 1

run_current: 0.580

hold_current: 0.500

stealthchop_threshold: 999999

​

[extruder]

step_pin: PB3

dir_pin: !PB4

enable_pin: !PD1

microsteps: 16

rotation_distance: 33.500

nozzle_diameter: 0.400

filament_diameter: 1.750

heater_pin: PC8

sensor_type: EPCOS 100K B57560G104F

sensor_pin: PA0

control: pid

pid_Kp: 21.527

pid_Ki: 1.063

pid_Kd: 108.982

min_temp: 0

max_temp: 250

​

[tmc2209 extruder]

uart_pin: PC11

tx_pin: PC10

uart_address: 3

run_current: 0.650

hold_current: 0.500

stealthchop_threshold: 999999

​

[heater_bed]

heater_pin: PC9

sensor_type: ATC Semitec 104GT-2

sensor_pin: PC4

control: pid

pid_Kp: 54.027

pid_Ki: 0.770

pid_Kd: 948.182

min_temp: 0

max_temp: 130

​

[heater_fan controller_fan]

pin: PB15

heater: heater_bed

heater_temp: 45.0

​

[heater_fan nozzle_cooling_fan]

pin: PC7

​

[fan]

pin: PC6

​

[mcu]

serial: /dev/serial/by-id/usb-Klipper_stm32g0b1xx_100029000A504B5735313920-if00

# serial: /dev/ttyAMA0

# restart_method: command

​

[printer]

kinematics: cartesian

max_velocity: 500

max_accel: 3000

max_z_velocity: 15

max_z_accel: 100

​

[board_pins]

aliases:

# EXP1 header

EXP1_1=PB5, EXP1_3=PA9, EXP1_5=PA10, EXP1_7=PB8, EXP1_9=<GND>,

EXP1_2=PA15, EXP1_4=<RST>, EXP1_6=PB9, EXP1_8=PD6, EXP1_10=<5V>

​

​

######################################################################

# BigTreeTech TFT TouchScreen emulated 12864 mode

######################################################################

​

[display]

lcd_type: emulated_st7920

spi_software_miso_pin: PD8 # status led, Virtual MISO

spi_software_mosi_pin: PD6

spi_software_sclk_pin: PB9

en_pin: PB8

encoder_pins: ^PA10, ^PA9

click_pin: ^!PA15

​

[output_pin beeper]

pin: PB5

1
F-K87•

I see that you are missing a ! in front you're enable_pin PB1 on the z stepper (enable low).

1
CommonInterfaceOP•

That was it, thank you so much!

1