r/Glocks•
Mallen

Another Glock 23 Troubleshooting Question

So I have had my Glock 23 Gen 3 for a little over a month now. I have run about 1200 rounds through it and have experienced a persistent problem that has me worried as this is my carry gun. Every time I have gone out and shot I have experienced about 3-4 failure to eject. I have cleaned the gun and not cleaned the gun, tried another magazine (Glock factory) and the results are the same. I am shooting Winchester white box and some once fired BVAC. Now I know this is on the lower end of ammo, but I have seen multiple posts that peoples Glocks can eat anything and would like the same. I even went ahead a fired a box of Speer Gold Dot 180gr GDHP (my carry ammo) and it jammed one time.

I went out yesterday after a good cleaning and had 5 FTE today I went out and had only one FTE on the last magazine on a round that was very questionable looking. I also experienced a problem with the slide not locking back after the last round on 2 of my mags and this while not as bad as FTE is still pissing me off? Any ideas on whats going on?

Finally one last question about cleaning, do you clean after every range trip or just give it a wipe down?

Posted Nov 4, 2012, 8:58 PM UTC

322
INEEDMILKG19 Gen2 • G19 RTF2 G•

What is happening when it is failing to eject?

Is the casing still stuck in the chamber?

Is it stovepiping?

The failure to lock issue is probably separate from the FTE problem (and frankly, not nearly as important to your well-being).

Did you buy this gun new?

I am OCD about my Glocks and clean the bore, at minimum, every time I shoot them.

4
MallenOPG17 Gen4 • G19 OD Gen4 • G23 Gen3 • G27 Gen3•

Stovepiping.

2
INEEDMILKG19 Gen2 • G19 RTF2 G•

Which ejector do you have?

3
MallenOPG17 Gen4 • G19 OD Gen4 • G23 Gen3 • G27 Gen3•

Says 1882 on it.

2
INEEDMILKG19 Gen2 • G19 RTF2 G•

The new Gen4 .40 extractors originally didn't have markings, but the newest ones have "28926" on them. This may or may not be causing the problem, but I would still put a call into Glock and ask for them to send you one (if they require you to be an armorer, just order one from the LWD site).

Did you buy this gun new?

Is there any way that the angle of the ejector arm has been damaged in any way?

Have you ever done a detail-strip of your gun?

How much experience do you have with shooting pistols?

4
Barry_McKackinerG23 Gen3 + G19 Gen3 + G19 Gen4•

I'd say do a detail strip of the slide, check the extractor and it's plunger & spring to make sure there is enough tension.

I bought a used Glock 23 gen 3 with the 1882 ejector and have had no issues with it. Granted I have a brand new tungsten guide rod and spring in it, but I've used reloads and cheapo ammo through it for 250 rounds with zero issues.

4
ImThaBeanG23 Gen3/ G42 Gen4•

I say, get rid of the Winchester White box. Those are junk rounds. I had a few FTE's w/ them. Not once have I had an issue with Federal, american Eagle, TulAmmo, Speer, Hornady, PMC, Remington & Winchester Ranger.

Spend the extra buck or 2 and get something better.

3
MallenOPG17 Gen4 • G19 OD Gen4 • G23 Gen3 • G27 Gen3•

Aye I agree as well. Worrying part is was jamming with my expensive carry ammo.

2
INEEDMILKG19 Gen2 • G19 RTF2 G•

Yea my original thought was the ammo, but if it's happening with a variety of ammo then it is something else entirely.

3
regulator_crackaG19 Gen4, G23 Gen4, G27 Gen4, G21 Gen4, G17 Gen4•

Yep! I personally have never had this constantly reported issue with wwb,*Walmart boxes at that, but that is not relevant here. The Gold Dots are the concerning issue. INEEDMILK seems more informed than I on this and I too would contact Glock asap. They can easily help you check the extractor or other issues. *Did you add any +1/2 mag extenders by any chance? *Retracted question, I re-read and see you have verified different mags.

3
ImThaBeanG23 Gen3/ G42 Gen4•

Stress test (if possible). Load all the mags you have and dump them with some rapid fire. This really depends on your range and Range Master.

Almost certain that this is ammo related. My buddy has a G22 Gen 2 that had the same issue with white box.

3
MallenOPG17 Gen4 • G19 OD Gen4 • G23 Gen3 • G27 Gen3•

Did this as well. Functioned fine for 200 rounds with all types of shooting. 200-400 random FTE.

2
ImThaBeanG23 Gen3/ G42 Gen4•

What that with the Winchester or did you switch out to another brand? All the Walmart's around me, the Federal is roughly $2 more than white box.

3
[deleted]•

Around 700 of my Glock 22's 1000 rounds have been WWB. It has one FTE and that was in the first 50 rounds with Federal. WWB have never given me an issue.

2