PeylixMK7 EQT FBO IS38 E85 | 2dr Master Race!•

Start perusing the part out threads on VWVortex and other forums. That and start calling all your local junk yards and such and check with them.

Those are your only "not breaking the bank" options. Otherwise you're buying new at a premium, not counting prep, paint, blend.

1
poolsclsdOP•

Yeah I kind of figured at minimum I'd be spending around $400. I'll go looking ar9und the forums though. Thanks!

1
imoc08•

You may be able to use some plastic or epoxy and try and rebuild that tab, there are quite a few youtube videos.

1
poolsclsdOP•

I was thinking about doing something like that, I just wasn't sure how plausible it was. Time to research I guess. TY!

1
BierOrk•

Have you removed the bumper and inspected the tabs and the mounting blocks?

In my experience the plastic mounting blocks break more easily than the tabs on the bumper itself. Most likely they need to be replaced.

1
OADominicMk6 Driver's Ed. Stage I•

what part of the world

1
poolsclsdOP•

California USA sadly 🥲

1
OADominicMk6 Driver's Ed. Stage I•

Mmm. I had good luck before with a junkyard. Google search a local junkyard and they usually have a vehicle list on their site. I had luck with that

2
poolsclsdOP•

Thanks, I'll take a look at some local sites and see if they have anything I can use

1
lkmama•

Might be a complicated swap because of the sensors in the bumper, but you can look online at car-part.com to see if there are any available at an auto dismantler. It might also be worth taking it to a auto body shop for an estimate, just to see what it would cost to have replaced professionally.

1
poolsclsdOP•

I have called a couple shops to try and get and estimate, but when I tell I'm paying cash they don't get back to me sadly. DIY is kind of my last resort

1
gnrc•

I have the same issue.

1
poolsclsdOP•

Have you gotten an estimate for repairs yet? I'm kind of curious to get ball park of how much it would cost

1
gnrc•

No I’ve been thinking about doing it myself cheaply if I can. With like zip ties underneath or something. My car is a mk6 with like 140,000 on it. I’m not trying to spend anything on cosmetics.

1
poolsclsdOP•

Same here mk6 but mines floating around 90k. I got a hell of deal bc the guy before me wrecked it but couldn't afford to fix the bumper and sold it to a dealership.

1
CapIndividual8784•

The way bumpers are designed are so that when they get hit or caught on the edge to rip off. you have to remember that it’s not a bumper. It is a bumper cover the steel bumper is under it. It is just a body fashion for looks. You can clean out any ripped pieces that are stuck in the bracket the bumper snaps into on the bottom of the fender you can break off of one piece that is ripped take the the screw out on the end in the wheel well that holds the bumper on snap it back in the best you can find a washer to put on that screw so it grab some more of the rubber. Screw it back on after it snapped and you might get lucky.

1
CapIndividual8784•

And yes, with that year you might get very lucky I have that car too same color. There are used parts finder websites. You can search your part your year and even the color you might get lucky.

1
poolsclsdOP•

I'm gonna keep an eye out, but thanks for the other post as well! I actually didn't know it was designed that way, I might try finding a diy fix for it using clips and screws.

1
CapIndividual8784•

No, don’t do that! Just study how it goes on there like I said, the part of the bumper, is designed to rip apart that’s why it is thin. If you flatten out the best, you can even heat it up with a hot air dryer and take a clamp to get it back into shape clean out the clip that it goes into. It’ll snap back in then just put the screw that is on the end of the bumper in the wheel well back in it, if it doesn’t hold well, you can put some two-part Apoxsee glue in the groove just a little bit put it back together and tape it till it dries and it should hold just fine. Lots of people make that mistake and try to screw it back together again.

1
CapIndividual8784•

I am a retired autobody technician with several certifications specializing in bumper repair, not tooting my own horn, but you’re not going to get any better advice other than taking it to a shop and having them repair or replace it

1
poolsclsdOP•

Yeah that was like my first plan, I'm more so looking at other options as a last resort. A couple of autobody places I've called only take insurance claims sadly

1
CapIndividual8784•

just search mobile auto body repair services in your area. These are the guys that fix cars on used car lots and at your home.

1