HP to Dell trunk not working
Hello! I'm in need of a little assistance. I suspect that there's an issue with our switch OS on the dell side, but I need a sanity check.
I'm attempting to create a trunk between an HPE SN2010M and Dell S4048ON. The HP is running OS version 3.10.3004 and the Dell is on OS 9.14(2.0).
On both switches I connected port 13 with a DAC cable.
I really appreciate any input, thanks!
When I bring everything up the way I believe it should be I get this result:
I can ping the HP from the Dell, but I can't ping the Dell from the HP.
SP10GStack1#ping 10.1.2.62
Type Ctrl-C to abort.
Sending 5, 100-byte ICMP Echos to 10.1.2.62, timeout is 2 seconds:
!!!!!
Success rate is 100.0 percent (5/5), round-trip min/avg/max = 0/0/0 (ms)
HPSw1 [standalone: master] # ping 10.1.2.60
connect: No route to host
HP show ip route (this is concerning)
HPSw1 [standalone: master] # sh ip route
Flags:
F: Failed to install in H/W
B: BFD protected (static route)
i: BFD session initializing (static route)
x: protecting BFD session failed (static route)
c: consistent hashing
p: partial programming in H/W
Warning: Number of HW failed routes is 1
These routes are marked with 'f' flag
VRF Name default:
------------------------------------------------------------------------------------------------------
Destination Mask Flag Gateway Interface Source AD/M
------------------------------------------------------------------------------------------------------
1.1.1.0 255.255.255.0 f 0.0.0.0 vlan900 direct 0/0
Dell sh ip route
SP10GStack1#sh ip route
Codes: C - connected, S - static, R - RIP,
B - BGP, IN - internal BGP, EX - external BGP,LO - Locally Originated,
O - OSPF, IA - OSPF inter area, N1 - OSPF NSSA external type 1,
N2 - OSPF NSSA external type 2, E1 - OSPF external type 1,
E2 - OSPF external type 2, i - IS-IS, L1 - IS-IS level-1,
L2 - IS-IS level-2, IA - IS-IS inter area, * - candidate default,
> - non-active route, + - summary route
Gateway of last resort is 10.1.1.254 to network 0.0.0.0
Destination Gateway Dist/Metric Last Change
----------- ------- ----------- -----------
*S 0.0.0.0/0 via 10.1.1.254, Vl 10 1/0 284w2d
via 10.21.1.254, Vl 21
C 10.1.0.0/16 Direct, Vl 10 0/0 284w2d
C 10.21.0.0/16 Direct, Vl 21 0/0 284w2d
C 192.168.198.0/24 Direct, Vl 13 0/0 284w2d
HP switch show interface:
Eth1/13:
Admin state : Enabled
Operational state : Up
Last change in operational status: 0:22:48 ago (3 oper change)
Boot delay time : 0 sec
Description : toSP10GStack1eth1/13
Mac address : 9c:05:91:62:d8:62
MTU : 9216 bytes (Maximum packet size 9238 bytes)
Fec : auto
Operational Fec : no-fec
Flow-control : receive off send off
Supported speeds : 1G 10G 25G
Advertised speeds : 1G 10G 25G
Actual speed : 10G (auto)
Auto-negotiation : Enabled
Width reduction mode : Unknown
Switchport mode : hybrid
MAC learning mode : Enabled
Forwarding mode : inherited cut-through
Dell show interface
TenGigabitEthernet 1/13 is up, line protocol is down
Description: HPsw1port13
Hardware is DellEMCEth, address is f4:8e:38:05:7b:29
Current address is f4:8e:38:05:7b:29
Non-qualified pluggable media present, SFP+ type is 10GBASE-CU3M
Medium is Twinax Copper
Interface index is 2098692
Internet address is not set
Mode of IPv4 Address Assignment : NONE
DHCP Client-ID :f48e38057b29
MTU 9216 bytes, IP MTU 9198 bytes
LineSpeed auto
Flowcontrol rx on tx off
ARP type: ARPA, ARP Timeout 04:00:00
Last clearing of "show interface" counters 284w2d2h
Queueing strategy: fifo
Relevant HP Configs from running config: (Omitting non-relevant things here)
##
## Interface Ethernet configuration
##
interface port-channel 10
interface ethernet 1/4 speed auto force
interface ethernet 1/7 speed auto force
interface ethernet 1/10 speed auto force
interface ethernet 1/13 speed auto force
interface ethernet 1/1-1/4 switchport mode hybrid
interface ethernet 1/13 switchport mode hybrid
interface ethernet 1/20 channel-group 10 mode on
interface ethernet 1/22 channel-group 10 mode on
interface ethernet 1/4 description "uplinkToCore"
interface ethernet 1/13 description "toSP10GStack1eth1/13"
interface vlan 5 description "native"
interface vlan 10 description "legacy"
interface vlan 14 description "iSCSI FD2"
interface vlan 15 description "office"
interface vlan 21 description "maganement"
interface vlan 25 description "production floor"
interface ethernet 1/4 shutdown
##
## LAG configuration
##
lacp
##
## VLAN configuration
##
vlan 5
vlan 10
vlan 14-15
vlan 21
vlan 25
vlan 45
vlan 204
vlan 900
interface ethernet 1/1-1/4 switchport access vlan 10
interface ethernet 1/1-1/3 switchport hybrid allowed-vlan all
interface ethernet 1/7-1/12 switchport access vlan 45
interface ethernet 1/13 switchport access vlan 10
interface ethernet 1/13 switchport hybrid allowed-vlan all
vlan 45 name "iSCSI"
vlan 204 name "vMotion"
##
## L3 configuration
##
vrf definition mgmt
interface vlan 1
interface vlan 5
interface vlan 10
interface vlan 14
interface vlan 15
interface vlan 21
interface vlan 25
interface vlan 900
interface vlan 900 ip address 1.1.1.1/24 primary
interface vlan 900 ip arp timeout 1500
Relevant Dell Configs from running config: (Omitting non-relevant things here)
protocol spanning-tree rstp
no disable
hello-time 1
max-age 6
forward-delay 4
bridge-priority 0
interface TenGigabitEthernet 1/13
description HPsw1port13
no ip address
mtu 9216
switchport
switchport mode private-vlan trunk
flowcontrol rx on tx off
no shutdown
interface Vlan 10
ip address 10.1.2.60/16
tagged TenGigabitEthernet 1/13,1/32
tagged Port-channel 2-4,40
untagged TenGigabitEthernet 1/8,1/26-1/28,1/33-1/34,1/36-1/47
no shutdown
interface Vlan 15
description Office
no ip address
tagged TenGigabitEthernet 1/13,1/32
tagged Port-channel 2-4,40
no shutdown
interface Vlan 25
description Production Floor
no ip address
tagged TenGigabitEthernet 1/13,1/32
tagged Port-channel 2-4,40
no shutdown
ip route 0.0.0.0/0 10.1.1.254
ip route 0.0.0.0/0 10.21.1.254
ip route 0.0.0.0/0 192.168.203.254
Posted Nov 12, 2024, 8:07 PM UTC
116