Repairing broken traces on a flexible PCB

repair

I got my hands on an almost operational Casio FH25 compact camera (the one that shoots video up to 1000 FPS). The only problem is that rear panel controls don't work at all. I traced the problem to broken leads in a flexible PCB connector.

There are 15 leads, 7 in the upper row and 8 in the lower. Upper leads seem to be connected well, lower ones unfortunately are broken off.

The whole connector is 4.5 mm wide, so fixing it with solder is orders of magnitude beyond my current abilities.

I tried connecting them back together with conductive paint (silver powder based glue) but the leads' pitch is comparable to the grain size I had, so no good.

Do you have any tips for me? Maybe reflow soldering with SMD paste?

http://imgur.com/a/0Bk8G

Posted Jul 21, 2013, 10:54 AM UTC

412
djkrugger•

I would try cutting the tip and flattening it so to move the contact area a bit higher, this if the length needed allows you of course. like this

EDIT: added pic.

2
obsa•

Who can tell me why the traces are shaped that way?

I think you could try a touch of SMD paste on one or two traces, reflow it, and see how it looks/feels after.

A better option would be to figure out if you can source a replacement cable somewhere. Lots of googling may be necessary, or it might be listed right on eBay. Depends on a lot on the repair community for the device. Maybe find a camera repair shop that could order it for you.

1
him_againOP•

It's not a cable, it's an integral part of the back panel PCB. I'm constantly scanning ebay, bitmit and others for a cheap busted FH25 to source parts from.

The camera itself is not in production anymore and official parts are no longer available.

I don't want to spend a lot of cash on it either, it's just a good opportunity to have a working "sort-of highspeed" camera for next to nothing :-)

1
orias0_o•

Why not bridge over the interrupted traces?

1
him_againOP•

Well yes, that is the general idea, the question is how? They are way too thin to solder reliably.

2
quitte•

The lines being flat and on a flexible plastic will make almost any fix break again.

Maybe you can find a Ribbon cable that is identical on the broken end - then sand down or dissolve the plastic on the bottom. Finally use 3M Z-Axis conductive tape to join the two cables?

1
orias0_o•

It would be best to find a replacement cable.

1
RooboticsRepair tech.•

You might be in luck: molex 'ffc' start by figuring out the pitch from the centers of two connections and go from there, see if you can find one with the same staggering pattern.

1
him_againOP•

Interesting. Do you have any pointers on how to attach the replacement terminal to the damaged one?

1
RooboticsRepair tech.•

You might have some luck with thin copper tape(the kind with an adhesive backing), so long as the added height doesn't mess up contact or make it not fit well (likely) Aside from that those sorts of connectors really don't lend themselves very well to repairs.

I've done lots of microsurgery/mods but never a FFC cable.

2
balboared•

It looks like the connector is designed to sit on the flex (spring-loaded pins?), so you also might have to be concerned about how flat the repair is. Solder is really your only hope, but it may not be strong enough by itself. That would depend on how the traces broke, since that section isn't really designed to be flexible. I would find some thin solid copper wire a little narrower than the broken traces, pound it flat with a hammer, then solder a short piece over each of the broken traces. If it all fits, it'll last a long time.

1
Pure3d2•

Use magnet wire. Use sandpaper to strip off the enamel (usually red color) from the wire on the area where you intend to solder. Magnet wire is soft enough to be pounded flat.

The magnet wire that radio shack sells might be too thick. If you can find an old motor that has super fine magnet wire in it, that would work.

You will need a very good magnifier or a microscope to do this level of soldering. I've repaired an XBOX360 motherboard with a lifted solder pad using this same technique.

Link

1