r/SSBPM•
Wraith557

C-stick not working on Dolphin?

I use Dolphin 4.0-648 and have followed all of the steps listed here to setup Netplay for Project M. The only problem is that when I play online, my C-stick will stop working (or only work intermittently) after I use it to perform a few aerials.

I don't think this is a problem with my controller or my Mayflash Adapter, because in the properties for my controller the computer reads all of my inputs on the C-stick. My inputs also register correctly in the Dolphin configuration for GC controllers. I have tried using both ports on my Mayflash and multiple USB ports on my computer as well as changing the radius for C-stick inputs in Dolphin, but all give the same result. When I play Melee netplay, the C-stick always functions normally and doesn't give me any problems.

Are there any known issues about this problem or does anyone have a way to fix it? Thanks in advance

EDIT: Thanks everyone, your responses were extremely helpful! I set my dead zone in Dolphin to 10 and everything seems to be working normally now.

Posted Jun 4, 2014, 12:55 PM UTC · edited

511
Spectrabox•

I had the same thing happening, I set the deadzone to 10 and it works for me now.

3
Wraith557OP•

Thanks, I never knew what deadzone actually did in Dolphin so I usually just messed with the radius. I'll try changing deadzone when I get home

1
pmstr•

The settings I use are dz 35 and radius 100. I was having the same problem.

1
Wraith557OP•

Thanks, I'll experiment with the dead zone. Usually I keep the radius around 70-90 but I can mess with that to see what works best

1
demonryder•

Deadzone is just the area where the control stick will not actually imput a command in the game, so with no deadzone it is pretty much always displaying a direction, but in smash bros if you go from one direction to another on the c stick without going back to the neutral position, the second direction doesn't actually do anything. So having a dead zone lets it reset back to neutral correctly. In my experience you just need to increase it enough so that the dot turns grey, meaning there is no input detected. For me that is only like 5, but if you have a more loose c stick you may need to increase it more.

1
Wraith557OP•

I've been messing with the dead zone and on 5 it was blinking between red and grey, but I turned it up to 10 and everything seems to be working perfectly. Thanks for the advice!

1
poppawheelie•

it might indeed be a mayflash/controller issue because I am experiencing the same thing but in melee. The c stick registers in setup 100% of the time, but for some reason in game c-stick commands are intermittent and don't always activate. I have just stopped using c-stick.

this current post has some similar info and solutions, check it: http://www.reddit.com/r/SSBPM/comments/2790eb/issues_on_dolphin/

set a deadzone /etc...

2
Wraith557OP•

Awesome! Thanks, I'll try that as soon as I get off of work

1
PoisonRain•

I posted this in a similar thread:

Look at the Deadzone for the c-stick. A deadzone is the area where the c-stick is considered neutral, not pressed in any direction. If the deadzone is too small, the c-stick may be considered to always be pressed in some direction (but will only trigger when the position changes or when the stick is checked, like for sdi). If it's too large, it will never register even when pressed all the way. You want it in the middle somewhere so that it will register when, and only when, you mean it to.

Edit: Picture

Hope that helps!

2
Wraith557OP•

This is immensely helpful, thank you! I was never sure what the dead zone setting did, so I always left it at 0. But that's too low, which explains why some directions of the C-stick throw out moves more often than others, it must be registered as constantly in one direction.

1
PoisonRain•

Glad to help! :D

2