r/trees•
jpstudly

Slapped together a killer and easy $3.50 waterfall bong. Instructions in comments.

Slapped together a killer and easy $3.50 waterfall bong. Instructions in comments.

Posted Sep 3, 2015, 5:35 AM UTC

19
jpstudlyOP•

I decided I wanted to try one of these and took a trip to Lowe's.

I started out by heading to the plumbing and faucet repair section and picked up;

1 foot of 3/8" interior diameter surgical tubing

1 set of matching interior diameter gaskets

And 1 nipple adapter of the same interior diameter screw adapter. Not sure what the actual name of the piece is, but it's an obvious bowl shape.

After that I was done with the hardware and headed to the registers where I picked up an ice cold soda which I finished on my way home. When I got there I headed to the garage and grabbed a dremmel tool an put a hole just large enough for the nipple to fit through in the cap and a carb I could cover with my thumb close to the bottom. If you don't have a tool you can make this with you can use a sharp hot knife, but be careful you could seriously hurt yourself being wreckless.

Now that the holes are made we just have to assemble it. Put a gasket all the way on to the nipple and insert the nipple in the cap to make a bowl. If you are a champ and can take a rough hit you can skip to the directions for use. If you are like me and have bitch lungs or like a smoother hit, put another gasket on the bottom of the nipple to make a seal on both sides. All that's left is to cut your desired length of hose, I did about an inch and a half off the bottom and wish I did a bit longer. Insert your new length hose onto the nipple and you are ready to go.

Directions for use:

  1. Pack your bowl, be aware of the hole size.

  2. Fill bottle with water and cover carb with thumb.

  3. Carefully screw on cap not too tight and be careful not to squeeze the bottle. This is the equivalent of the guy with greens blowing into the bong. I hold it with my thumb and index finger wrapped around the neck and suspend it while I hold the carb.

  4. Place the bottle on a table outside or the edge of a sink and simultaneously release the carb and light the bowl. Tend to it while the water takes one long drag and cover the carb when you think it's ready. I go pretty far down or till it's cashed.

  5. Unscrew the cap and remove. Quickly release the carb and start clearing it through the top. I recommend you take a SLOW long hit as opposed to just ripping it, it can be very rough. Hit it and pass or clear it yourself. Then just pour out the water, hit the cash can, and pack the next.

Be aware, I have an average to above tolerance and this hits me pretty hard. Also sorry if this has to be translated, I'm an [8] this guy whoops my ass. I'm seriously debating some serious financial choices of mine.

Enjoy!

TL;DR: look at the picture and you can probably figure it out. Your a man, or empowered woman, no need for instructions! Enjoy!

1
billcarlsby•

this is still way more complicated than waterfalls i make. what the fuck is the point of the tubing? unnecessary.

1
jpstudlyOP•

It makes it hit a whole lot smoother. Ima bit of a bitch so I need it

0
billcarlsby•

i dont think you understand how fluid dynamics work. the tubing literally does nothing. the smoke doesnt pass thru the water like a bong, it just displaces the water that is leaving the bottle at the bottom. think about it... its an entirely unnecessary part of the piece.

0
jpstudlyOP•

If it gets pulled down through to tubing it does very much pass through the water

0
billcarlsby•

you might wanna watch it next time you use it. the water level remains the same inside and outside the tubing. the smoke wont pass thru the water at all, just sits on top of it. unless you somehow managed to break the laws of physics.

0