Updated FAQs

Tips and Tricks

Given that version 1.0 is being released later today, I think it's possible there will be a few new players hanging around. The current FAQs are a little outdated, so here goes.

If you can think of any other likely questions, by all means post them, and I'll incorporate them in to the OP if warranted.

Original FAQs written by u/Swatlord.

If you don't understand how a particular mechanic works, check out the excellent Prison Architect Essential Ideas Guide, by u/Ask_Me_Who.

For more general tips and tricks, I made a post for that here.

#How do you get more money?

To start with, take up some grants. The Basic Detention centre is a good start, because completing it will give you a functioning prison and unlocks further grants. Taking in prisoners will also net you a small cash bonus.

In the medium to long term, your best source of income will be workshops. A prisoner shop will also help by a few hundred dollars, though it's more useful for lowering your prisoners needs. You can also look to make savings in how your prison operates, like employing prisoners to work in your kitchens and to clean up.

You can also of course just edit the save file, look for the word "Balance".

#How do I turn off prisoner intake?

See the To-Do list, on the left of the screen? There is a timer ticking down until your next intake. Click it, and it will take you to the Intake section of your report file, or alternatively click on reports (bottom right) and select the intake tab. There you will see a series of sliders and a number in the centre of the page. The number represents how many prisoners you want. Click "none" on the left to disable intake.

#My prisoners aren't being let out of their cells, even in Free Time.

Use the Deployment tab to make sure your prison is secure. By that, I mean that your prisoners couldn't just make a run for it once they are out of their cells. If your prisoners need to travel between buildings, you will need a fence or perimeter wall separating the travel area from the wider world. Insecure areas will flash yellow.

#My prisoners or a particular prisoner wont work in the kitchens, laundry, etc. There could be several problems here. This could be because:

  • Part of the path is blocked, because either a part of it is Insecure, Staff Only, or of a different security level to the prisoner.

  • You haven't set any workers in those rooms under the Logistics tab. You will also therefore need Prison Labour, and the prerequisite Maintanance technologies unlocked.

  • The prisoner is not qualified to work in the assigned room. The Workshop and kitchens need their own safety course to be passed before the prisoner is allowed to work, and the library requires a prisoner to have passed the Foundation Education class.

  • Prisoners who are gang members will not work. They will also refuse to take part in any reform programs.

#How can I get more prisoners interested in/ successfully completing a reform program?

To be interested in a reform program, a prisoner requires to be free of suppression. Suppression is caused by spending time in Solitary, or being in the presence of armed guards.

In order to actually pass a reform program, two things need to happen:

  • One, the prisoner needs to be able to turn up on time. This is a problem if he is currently being punished, or if his cell is a long way away from the classroom. You should bear in mind that reform programs require Work time in the Regime.

  • Two, the prisoner needs to be able to concentrate. This means that his needs are low, and that he is not currently suppressed.

#My power keeps shorting out

Again, multiple possible causes.

  • One cause is if your generator is overloaded. This means that it is trying to power too many things. You can add more power by adding capacitors, which need to be installed directly next to your generator. If that's not enough, you will need an additional generator, which brings us to the next possible problem:

  • Don't cross the streams. If you have more than one generator, their lines can not cross. You will need to keep the lines at least one tile separate.

#Why can't my workers do anything in this cell?

Cells occupied by gang members cannot be tinkered with, as they are considered dangerous. You will need to assign the prisoner another cell, by selecting the prisoner (left click) and then right-clicking a vacant cell. You could also de-zone the room.

#How do I detect tunnels?

When a dog passes over a tunnel, it will stop and start scratching at the ground. You'll hear the growling noise. The handler will mark the area with a little yellow flag. You can have false positives, but if you see a few flags then you may want to search the nearest toilets, since that is where tunnels start.

Searching toilets during a shakedown or cell block search only has a small chance of uncovering tunnels, but specifically searching a toilet manually or dismantling it is guaranteed to find the tunnel.

#How far do sprinklers and fire spread?

Sprinklers can detect fire up to four tiles away, including diagonally, but they are not reliable. I would suggest a spacing of three. Fire can also spread up to four tiles away from an initial source, but they tend to burn out after three. So if you space your buildings three tiles apart, they aren't guaranteed safe from spreading fire, but they are very likely to survive, and definitely long enough for you to call firefighters.

#How do I edit the save file?

While ingame press escape and click on the "open saves folder" button, this will open another window that has a saves folder in. Open the saves folder and a list of saves should be there. Each save will have an image file and a text file. Next, right click on the save you wish to edit, and choose to open it with notepad, or any other text editing software. From there, you can then locate what you wish to change and then save.

Alternatively, you will have to find your "appdata" folder, then enter "Local", then "Introversion", then "Prison Architect" and finally "saves". Find your file and open it as mentioned before.

Once you have edited the save file (and saved your changes) you will need to load the save again for the changes to take effect.

#How do I join the official wiki?

Here is the official support thread.

Posted Oct 6, 2015, 2:44 PM UTC · edited

910
Loading comments…