Timbo1986'96 ZJ Laredo 4.0•

Saw this over at Jeepforum, looks like a blast!

2
ikidd•

Ah, the awesome cornering ability that is a ZJs birthright. That 360 could get you in a lot of trouble going in hot and catching a rut, though I dont' see much opportunity to really wind it up on that course. Looks like fun though.

2
comptiger5000OP98 ZJ 5.9 Limited [NY]•

Yeah, I was definitely much slower than most through the nasty rutted sections. Ruts and really tight corners are the major slow-downs for the ZJ on a course. If you get the suspension set up right, it takes the fast slaloms very well though.

1
ikidd•

Suspension is sounding crunchy, or is that the rut noise?

1
comptiger5000OP98 ZJ 5.9 Limited [NY]•

Yeah... I've got a few things to fix. There's a lip on the new bumpstop cups that's hitting the left front spring a little at times, so I have to screw with that (it was making a ton of noise). And I got a few nice pops from the axle end of the track bar, so that'll be getting a new (slightly larger) bolt that's tighter fitting in the holes and can't slip.

1
comptiger5000OP98 ZJ 5.9 Limited [NY]•

As far as winding it up a bit, I did see close to 5k in first a few times. Last month, I tapped the limiter at 6k a couple times in the fast stretches. The motor is heads/cam and a few other tweaks.

Here's some details on the setup:

It sits just a hair taller than stock height (within a 1/2"). It's got hacked up "custom" springs, around 280 lb/in rate up front (stock is 190) and progressive in the rear, around 320 - 350 lb/in at ride height, close to 600 at full squish (stock is 160 and linear). Rear sway bar is removed, front is upgraded from the stock 26mm to a 29mm Addco bar. Shocks are Bilstein 7100s, valved 400/100 up front, 360/80 in the rear. Bumpstops are stock in the rear, the fronts are the rear bumps from a 99 - 06 Chevy 1/2 ton pickup.

I ran with the 231 in 4hi, trans kept in 1st. 3.73s in the diffs (stock open D30 up front, D44a in need of new trac-lok clutches in the rear). Tires for the day were 225/75R16 Hankook Dynapro MTs (if you look at the video from the previous month, I was on my snows, which are 235/70R16 Nokian Hakka R2s). Both of those sets of tires sit on stock 16x7 wheels with 3/4" spacers behind them.

1
ikidd•

How was the body roll on the corners with the rear swaybar out? Have you run it with it in? I imagine it's pretty minimal with those springrates.

I'm the same on the trashloc, need to get up the ambition to pop out the carrier and redo the clutch pack. I have it all sitting there along with new carrier bearing and seals, just need to get on it. If I put in a new pinion bearing though, then I have to preload it and I don't have my inch-lb dial torque wrench anymore (never lend tools).

1
comptiger5000OP98 ZJ 5.9 Limited [NY]•

I put the current rear springs in when I deleted the bar, and the roll is very, very minimal. It's similar in roll and overall handling balance to the previous setup of 260 lb/in rear springs and the stock 16mm rear bar, but the suspension is much better behaved now (less twitchy, rides better). The stock rear end link design binds a lot as the suspension travels due to the sandwiched bushings and I didn't feel like designing / making better end links for it, so I just took the bar out and changed the spring setup instead.

1
jhowlett1997 ZJ / 2013 GC Trailhawk•

Dude this is awesome. Love seeing a 5.9 used like that. I love to do something like that

1
InvalidKoalas'98 ZJ Laredo•

Where is this? I'm from CNY too so just wondering.

1
comptiger5000OP98 ZJ 5.9 Limited [NY]•

They're run with CNY SCCA at a few different locations. The schedule is here: http://cny-scca.com/rallyx/events.php

1