r/Coffee•
RedFlocks

Question about LIDO 2 grind size.

I'm afraid that there is something wrong with my LIDO 2, but I'm not sure. I've felt for a while that the grind on it was unusually coarse and inconsistent. When I grind at 1+2 or 3 for Chemex, I have a fairly large amount of fines which stick to the side of the cup. This always perplexed me since I though the LIDO was not supposed to make a lot of fines.

And then I just watched this video which shows the grind at 1 revolution and my grind at that setting is NOTHING like that. It's huge chunks and a lot of smaller pieces. Nothing nearly as consistent as that. As far as I can tell there is no part of the LIDO which allows for different calibrations, so why are our grind sizes so different?

EDIT_ Here's my grind at 1 revolution: http://i.imgur.com/OUrhTBo.jpg

EDIT2_ Here are more grind settings: http://i.imgur.com/wFXbh5f.jpg , http://i.imgur.com/TtttXqO.jpg

Now that I lay them all out like this, I feel like I have a good range of settings that is just lower than I thought they were. I still don't know if it's supposed to be so course at 1 revolution. The manual says that course grind goes all the way up to 2 full revolutions, but i can't even get that far without the ring coming off. Is that normal?

Posted Apr 13, 2016, 11:58 PM UTC · edited

314
egzwygartChemex•

How long have you had your Lido 2? If you have the newer burr set, 1+2 is wayyy too coarse. I run my Chemex from 11 to 13 depending on the beans. Start with 12 go from there.

5
RedFlocksOPChemex•

Yeah it's new. I got it for Christmas. The new burrs have different settings than the old ones? That might explain all my confusion.

2
beepbooppeepoop•

Yeah man, the new Lido 2 (same burrs as Lido 3 and Lido E) are different than the old ones. For a 1+0 on the old burrs, adjust to 0+10. I usually do chemex brewing at 0+11 or so. Aeropress gets 0+8 or 0+9.

3
CA_JimCortado•

Holy hell, dude. I just got my new Lido 2 today and tried grinding at 18 notches based on some recommendation here from like 2 years ago.

Same problem, way too coarse. I thought I was going crazy. I had no idea the new burrs were so different. I tried grinding at 12 and while it's still not perfectly dialed in, I'm finally in the right ballpark.

Thank you, u/egzwygart and u/beepbooppeepoop.

For the record, I'm brewing a V60 with a ratio of 28g:400g. I'm currently looking into changing up my method & ratio to fit the consistency of my new grinder.

1
egzwygartChemex•

Yep. The newer burrs are less aggressive, but easier to crank. OE also uses them in the Lido 3. Unfortunately, they haven't changed the instructions, yet, or at least they hadn't when I got my L2 in November. Look up settings for an L3 and that should solve your problems.

1
damnination333Chemex•

You may need to realign your burrs. Did you ever disassemble your LIDO for cleaning?

3
RedFlocksOPChemex•

I've realigned them before and I did again just before I started testing it out today.

1
AnomanderDoC - Pistol & Burnes•

Can you toss in some photos of your grind at a couple settings? Coin for scale or something?

It sounds like something is wrong with your grinder, but can't tell without seeing.

1
RedFlocksOPChemex•

I added pictures to the post.

1
jja619Coffee•

Are the "3" and "5" from zero? Those look super coarse. I pull shot at around 4.

1
RedFlocksOPChemex•

Yeah. They're all counted from the notch that came marked from the factory. The ring tightens completely just past the zero mark.

1
jja619Coffee•

Has it always been like that? Have you tried cleaning it out a bit?

1
PolskaR•

Whenever I compare grind settings with other Lido owners I do it from "relative" zero. That is not necessarily the premarked zero point which is apparent when you get the device but it is the point when the burr assembly moves freely. At the point that the assembly moves is my "relative" zero and from it comparisons can be made.

1
aeroeax•

I had a Lido E-T until I returned it. The ring burr has room to wiggle so unless you adjust the screws just right (really hard to do at least for me) they will be out of alignment.

1