Just need to express my joy that I'm back in the game.

Discussion

My printer has been down for going on 3 weeks. I tried everything I could think of to fix it. I was even just throwing parts at it. Got fed up and just left it alone for a few weeks. Today A buddy finally found out why it seemed like I was having filament slipping issues. I haven't printed anything in 3 weeks. I was starting to go through withdrawals. Its so addicting to print something and see the end result. I'm back in the game today and this thing is about to see more serious hours of printing. Never new how addicting this hobby was until my printer went down. My only wish is I could leave a print going while I sleep or away from the house but after having one Ramps smoke out on me, I refuse to leave my printer unsupervised.

Posted Oct 17, 2016, 12:43 AM UTC

45
[deleted]•

[deleted]

1
ThatTruthBombOP•

It looked like filament was slipping. I thought it was a clog. I changed the nozzle. I changed the neck. I bought a new stepper. I put in a new stepper. I put in a new MK7 gear. Turned out somehow the jog speed of my extruder got bumped up so it wasn't feeding filament correctly. (I suspect my sister accidentally did it somehow). ONE setting I over looked put my printer down 3 weeks and cost me money. Its literally one arrow that changes the job speed of the extruder in Simplify3D that got me so frustrated I almost just went and bought a new printer.

1
citrus_monkeybutts•

I had my board go out on my printer (blown thermistor port caused it to not work and the LCD port shorted as well) and caused my main printer to be out until I got a replacement. So I ordered one and paid extra for rush shipping to get it within a week instead of the estimated 3-6. When I got the replacement the LCD was working and all other ports were working except for the hotend thermistor again. So I had to fight with Wanhao support to get my board shipped back in. That took about 2 weeks, plus another 1 for shipping there, and another 1 for coming back with a new board.

Got the new board in on tuesday last week and got it installed, tested, recalibrated and back to printing. I've been printing almost non stop since then. Printed out new parts for my other printer, and then found out that my thermistor snapped in two (the glass bulb itself broke in 2) and I have to replace that, but I don't have spares because my only spares got used on my other printer and had exposed wires near the bulb.. so I had to order more of those, and FedEx decided to 'try' delivering it, and by try I mean they left a note and didn't even knock on my door.

So, I should be getting my new pack of thermistors tomorrow at some point, and if all goes well, I'll have my 2nd printer back up on wednesday.. which means I can print the parts out for my items 2x as fast.

TLDR; I had my printer out for 2+ months and finally got it back up this week as well, so I know your pain all too well.

1
Jomamma1Ultibots Kossel•

Good to hear you're back up and running.

I'm in the same boat, printer was down for 2 weeks. First a thermistor connection went bad, then I had a pretty bad clog and ended up wrecking the PTFE liner. Then after updating the firmware on my board I had some config issues to track down. Finally got it all sorted over the weekend and it's printing great.

1
ThatTruthBombOP•

Can you elaborate on the thermistor connection issue you had? I it seems like I spoke too soon. I printed something for 3 and a half hours with no problems. 30-45 mins into another print I get a "thermal runaway bed" error and my LCD says "MINTEMP BED". I just shut everything off and walked away from the printer.

1
Jomamma1Ultibots Kossel•

I would check your connections. For me I think it was just a bad crimp. I had a similar error about the hotend thermistor disconnecting (don't remember the exact message). I went along pulling & moving wires and the thermistor wire was broken at the ferrule. I'm not sure what caused it to fail. Before that it's been printing fine for about a year.

Ninja edit - I run octoprint. As the thermistor connection was failing you could see the temp graph go kind of crazy ( ~10 degree variations ). Might be useful if you run octo.

1