r/Coffee•
quitte

Hooking coffee maker to water line?

The coffee maker I would like to hook up to the water line uses a vibration pump which is fed by gravity via a solenoid valve from the tank. To my understanding the pump creates pressure severly higher than the 5 bar that the cold water line here is regulated to. So I'm thinking replacing the valve and feeding it pressurized water might just work?

If anyone can point me at actual datasheets or manuals of vibration pumps that would be very helpful. I forgot the specific model and manufacturer but because of a leak will soon replace all gaskets anyways so will find out.

Edit: The solenoid valve is a flow meter. I misremembered.

I watched a few videos on how vibration pumps work, and I think I get it now. They will typically allow pressurized fluids to go through instead of pumping a fixed volume on each vibration. Instead they increase pressure of the water flowing through.

My main problem remains: is it safe to feed pressurized water to a vibration pump? I recognize that I have to take measures to ensure that the flow of water stops when the pump stops.

Posted Dec 1, 2016, 2:19 PM UTC · edited

1817
swroastingS&W Craft Roasting•

Why not just install a float switch in the tank to keep it full? Hint: look at aquarium supplies to DIY.

7
quitteOP•

I haven't considered that before, since I assumed a vibration pump pumped volume units instead of increasing pressure. In that scenario it just didn't make sense.

Now that I know better and gave it some thought there are a few reasons: The tank connection is potentially leaky. I'd prefer not to have the water going in controlled by water going away only. I guess I could make it so the tank can only be refilled while the pump is running.

The other thing is that the tank is clear and the sensors are ugly. On the other hand I could move the sensor to the inside by adding a secondary smaller tank. Then the uglyness reduces to an overflow and air bleeding tube into the main tank.

Thanks.

1
Kalzenith•

Float valves require zero sensors, there's just a buoyant bulb that triggers a mechanical switch when the water level drops.

They're dirt cheap, no need to over think the problem.. if you think it's ugly, consider painting the reservoir

3
quitteOP•

That would be nice, except it lacks any safe-guard against a leak anywhere in the system. Any water lost will just happily be replaced, even if the float valve works perfectly fine. This is acceptable in a toilet, where it will just drain away in a safe manner. With a coffee machine that is way too dangerous.

u/Number1AbelLincolnFan : overflow protection doesn't help against a leak at any other place in the system.

2
aywwts4•

Good call, dealing with water damage in a home makes for a less than fun year of battling insurance companies and contractors. Can't imagine if it was a claim on a self modified coffee maker run amok while on vacation.

2
Kalzenith•

You can always install a drain line above the float. That way if the float valve fails, water will just drain back into your plumbing

1

Seems like you're way overthinking this. What you need is called a fill valve. Just buy a small one that will fit, run a water line to it and set the level you want. You will also need to set up an overflow line so your house doesn't get flooded if the valve sticks open.

4
[deleted]•

[deleted]

2
quitteOP•

It is indeed an easy solution and it does the job. It is however very unsafe. After having taken apart such a machine I know for a fact that just making sure the machine never runs out of water is a very bad idea.

The tank being rather low volume is an essential safety measure. A float valve with no additional safe guards entirely defeats it.

1
[deleted]•

[deleted]

2
quitteOP•

A direct connection of water to the pump was never an option. A solenoid valve between the water and the pump would have made sure that when no power is going to the pump the water supply is shut off. Since that seems to work okay for washers and dish washers I'm willing to place some trust in that.

As long as the solenoid valve works there is no water going into the machine unless the machine is brewing coffee. With a float valve water goes into the machine no matter why water is disappearing from the tank. Even if the valve is working perfectly fine.

1
[deleted]•

[deleted]

1