Maximizing Natural Gas Geysers
So, Brothgar beat me to posting on this, but I wanted to put up what I'd been working on for a few days anyway, and I think I can add some mathematical rigor to it.
Basically, as he pointed out in an earlier video, you can use the synergy between Natural Gas Generators, Fertilizer Makers, and Air Scrubbers to get way more power out of a Natural Gas Geyser than you would be able to with generators alone.
Requirements
You can break down the requirements of each building as follows (and we'll also assign a variable to the count of these building to be used for the math later):
| Building | Variable | Natural Gas (g/s) | CO2 (g/s) | Polluted Water (g/s) |
|---|---|---|---|---|
| Natural Gas Generator | G | -60 | +82.5 | +67.5 |
| Fertilizer Maker | M | +20 | 0 | -150 |
| Air Scrubber | S | 0 | -300 | +1000 |
| Natural Gas Geyser | Y | +100 | 0 | 0 |
Solving the System
Considering each of these resources, we can turn this into a system of equations:
| Resource | Equation |
|---|---|
| CO2 | 82.5G = 300S |
| Polluted Water | 67.5G + 1000S = 150M |
| Natural Gas | 100Y + 20M = 60G |
You could solve this with linear algebra, but personally I like solving these things by hand. First we can get the number of scrubbers per generator by solving the CO2 equation:
S = (11/40)G = 0.275G
Next, we can plug this into the Polluted Water equation to get the number of fertilizer makers per generator:
67.5G + 1000(11/40)G = 150M
M = (137/60)G
M ≈ 2.28G
Then we get to the Natural Gas equation, plugging the solution for fertilizer makers in to solve for the number of generators overall:
100Y + 20(137/60)G = 60G
100Y = (43/3)G
G = (300/43)Y
G ≈ 6.98Y
So this means each geyser can support about 6.98 generators; we can then plug this back into the solutions for the first two equations to get the total number of fertilizer makers and scrubbers:
M = (137/60)(300/43)Y
M = (685/43)Y
M ≈ 15.93Y
S = (11/40)(300/43)Y
S = (165/86)Y
S ≈ 1.92Y
So this means our final numbers are 7 generators, 16 fertilizer makers, and 2 air scrubbers, each with a little downtime. While that sounds all fine and good, there are a lot of considerations when actually building the thing.
Design Considerations
6.98 generators consume 418 g/s of Natural Gas, so one pump should do fine, conserving power once the pipe system is full of natural gas. Initially, you may want to add a filter just to get rid of any impurities that made their way in while building the complex, though.
All these machines will produce a lot of heat, so we may need a cooling system. At least, you should probably build everything out of Gold Amalgam, so that its overheat temperature is at least 125°C.
When all 7 generators are running, that's 5600W of power running on the wires; you can solve this by using Heavi-Watt wire, but personally I prefer the challenge of designing separate 1 kW subsystems. Note that each subsystem needs its own battery as a buffer, which you can also use to make sure your subsystem is correctly designed (if so, the battery will be full).
Example Build
However, I also built a really cool schematic template for the wiki, which mimics the in-game overlays, so I recommend checking it out there.
Power: In this build, the three generators on the bottom power internal subsystems, and the one on the right powers a few extra internals, with about 293W left over, which I use to power a clean water pump at my nearby Steam Geyser, and some doors which mostly don't consume power. The three top-left generators are completely free to power subsystems of my base. I included two manual generators; the one of the left for getting the main subsystem up and running, and the one on the right to run some fertilizer makers before the system starts, to help fill the complex with natural gas, which will displace most impurities (not Chlorine or CO2, but there shouldn't be much of that).
Liquid: This is pretty straightforward. However, if you design your own differently, just be careful to give each output a little segment of pipe to itself so that it can properly merge packets. I also included an external input of polluted water for priming the system initially. Be careful not to completely fill the pipes doing this (I did...), because it will back up the scrubbers, which will back up the generators, which will make everything fail. If you are pumping straight from the geyser like I am, make sure to use abyssalite piping, at least outside of the complex, to prevent the water from heating up your base.
Gas: Again, the little bends on the output are for proper packet merging. There is a filter lower-left used for removing impurities. I tried a mechanical filter (lower-right), but this is problematic because the pump will run until the pipes are backed up, so eventually it will just pump all the gas in the unfiltered output of the mechanical filter. Instead, I'd recommend just having the normal filter and then deconstructing it for a direct line once impurities are removed. I don't need all the power at the moment, though, so I haven't done it.
Part-time Subsystem: I wanted to make sure all of the part-time machines were on the same subsystem. For this, I use a gas valve for the upper-right generator, which is set to a flow rate just below 58 g/s (to make sure that we have just a little extra gas instead of depleting it gradually). This is then connected to the bottom fertilizer makers, the rightmost two of which have the lowest priority for getting polluted water (just because they're deepest in the branch tree of the pipes). Finally, air scrubbers run 100% of the time, even if they're not consuming 100% of the CO2, so to make sure they don't overconsume, I added an atmo switch controlling the top scrubber, which is set to "above 600g".
Corrections: I noticed the bottom scrubber didn't have enough pipe between its output and the main line. Instead of directly going right into the main line, I added a little bend up before entering.
Posted Jun 18, 2017, 8:25 PM UTC · edited