Jumpstarting - can't find an unpainted metal surface

I have a VW Jetta (2010). I've watched and read guides saying to:

  1. Both cars turned off, etc.
  2. Connect a red clamp to the positive battery (dead car)
  3. Connect a red clamp to the positive battery (donor)
  4. Connect a black clamp to the negative battery (donor)
  5. Connect the remaining black clamp to an unpainted metal surface (dead)
  6. Turn on the donor car, etc.

(I'm aware that it's common practice to just place the remaining clamp onto the negative battery of the dead car, despite warnings about sparking a hydrogen gas explosion upon disconnecting the clamps. I've done so myself before. But however small the risk is, I'd rather learn the safer/proper way.)

Thing is, I can't find any unpainted metal surface anywhere within reach! All guide examples show hoods where there are plenty of unpainted metal surfaces to clamp onto, usually the chassis, but just about everything under the Jetta hood is plastic, painted metal, or unpainted metal surfaces that I can't get the clamp to securely latch onto. There are some metal pipes leading to the engine that are unpainted, but none of the examples showed clamps on pipes that fluids might run through. Would those be safe to use? If not, what other options are there?

(Click for pics)

Posted Jun 22, 2017, 5:07 AM UTC

1212
Lars0Mechanical - Small Rocket Engines•

I have been in the same position myself.

I have always just put it in the negative terminal. The risk of producing gases is really only there if the battery is super dead-dead and has been that way for a while.

You need to have pretty clean water to be able to electrolyze a lot of it into hydrogen and oxygen.

11
Carorack•

Read the car manual. I guarantee it will show you where to make your connections.

10
civiljoeCivil/Land Development•

Might want to crosspost this to r/cars or someplace. Any protruding bolt on the car body would be useful for this. Just engage the jaws and rock the clamp a bit to bite through the paint. The

4
TurkishRambo30Mechanical - Manufacturing•

I always clamp onto the engine block.

4
TugboatEng•

Hydrogen is lighter than air, it doesn't linger much in the engine compartment of a car with the hood up.

3
tokyosuits•

What's on the front right of the engine? MAF sensor? Looks like unpainted metal from the picture.

0

Press backwards on the front of the tab on the plastic box with battery symbol(drivers side) and then pull up. U now have access to both battery terminals, they will either have plastic caps u pull off or bare metal. Now for the jump or charge: 1)On live car that is running, connect red to positive 2) then red to dead car positive. 3)then black the live cars negative 4) finally black on dead cars negative. Ull hear the running cars alternator be weighed down by the new load. 5) Wait a couple minutes. 6) start dead car. It will start, unless starter is dead. 7) do steps 1-4 in reverse.

In case there is any confusion, painted metal does not matter too much. The battery posts are not painted, ever. Also, the aligator clips will bite through ur paint and make contact as long as there is it is somehow attached to the chassis, but then again can u not find ur battery?

As for hydrogen detonation... stochiometery will stop that from happening. Do u ever have trouble lighting a propane grill? In real life ur not gonna blow up from jumping... EVER

Source:I have a 2008 mkv.

-1
lurkotatoComputer Engineer - Software•

They specifically wanted to avoid clamping both leads to the dead battery.

2

Oh, he said he wanted to "learn the right way". Quite literally there is only 1 right way to jump a car

-1
lurkotatoComputer Engineer - Software•

Doing it unsafely is not "the right way".

2

What is unsafe about the way I described? What is unsafe is trying to find some new place to clamp in hopes of finding a short back to ground.

-1