Hash_KetchumOP•

Hello everyone. I was recently gifted a stock Beta/kickstarter robo3d r1 and I have quickly come to understand why. Even after upgrades (control rod stabilizers, e3dv6 hotend, integrated leadscrew NEMA steppers for the Z axis), it can barely print ANYTHING successfully (and anything larger than a 1cm test cube appears to be a lost cause.

The extruder seems to randomly stop forcing filament through during prints, and my prints have parts of layers (and parts of walls) missing.

I am pulling my hair out trying to get a good print. Super excited to get printing and become a member of the community, but I really need some help to make it happen and I am at a loss for what to try next.

The bed has been leveled using the paper method (does not support auto leveling) and checked with a spirit level.

I am printing with Inland PLA (have tried light blue and yellow, the blue is a fresh roll opened last night to see if the yellow was moisture contaminated. The prints you see were printed at 205c on a bed heated to 60c with purple elmers gluestick to help adhesion.

The printer is hooked up to a raspberry pi running octoprint, and the models are being sliced on the newest version of CURA.

Any suggestions of what to try next would be helpful. Could this be symptomatic of a RAMPs board overheating?( no fan or bottom on the unit as far as I can tell). It did not seem to exhibit what I understand to be the symptoms of that (stopping and starting mid print) but at this point, everything is on the table.

3
Magnavis_Wanhao i3 Plus•

what print settings are you using?

1
Hash_KetchumOP•

Layer Height: .4mm
Flow: 100%
Enable Retraction: X
Retraction Distance: 3mm
Retraction Speed: 50mm/s
Print Speed: 40mm/s
Wall Speed: 20mm/s
Top/Bottom Speed: 20mm/s
Support Speed: 40mm/s
Travel Speed: 120mm/s
Initial Layer Speed: 20mm/s
Initial Layer Travel Speed: 120mm/s
Number of Slower Layers: 2
Z hop when retracted: X
Z hop height: 2mm
Enable Print cooling: X
Generate support: X
Build plate adhesion type: Raft
Raft air gap: .2mm
initial z layer overlap: .1mm
raft layers: 2
Raft print speed: 20mm/s


I slowed the print speed down a bit to see if it would print any better- it seemed there was a slight improvement, but then print quality dipped again and I think it may have been coincidental.

1
AddictedToComedyMP Maker Select v2.1 and Mini Delta•

Layer Height: .4mm

What size is your nozzle?

2
Hash_KetchumOP•

.4mm

1
isaacfankTevo Tarantula - P3Steel - HACKKA•

Yea layer height shoulnt be more than 80% of your nozzle size.

2
biglightbt•

The big guys are as follows:

Lower layer height to .2mm

Use your part cooling fan for PLA if that's what you're printing with.

Do not use a raft.

DO NOT USE A RAFT

DO NOT USE A FUCKING RAFT!!!!1

1
tenmonkeysinacircleKossel Mini, D-bot•

Try increasing the temperature. You say you've got an all-metal hotend - those require printing temperatures closer to the high end of the spectrum. That could help with under extrusion somewhat.

1
AutoModeratorMOD•

Hey there, I'm a bot and something you said made me think you might be looking for help! click here for our wiki entry on troubleshooting printers. If you still need help be sure to post plenty of information about your printing setup.

Here are a few questions that might be helpful

  • What printer are you using?

  • What material are you using?

  • What speed are you printing at?

  • What software are you using to slice the print and control the printer?

  • When did the problem start/has it ever worked correctly?

  • Does anything cause the behavior to change?

  • If posting an image of the problem, include some indication of the orientation it printed at, preferably photograph it on the bed. (Then we can focus on a specific axis)

If you are new to reddit, please read the guidelines on reddiquette, self promotion, and spam.

Also please post a resolution to your problem when you find one so that we know how to help others with your problem!

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

2
Nm456•

Have you set CURA to the correct filament diameter? Because it defaults to 2.25. and that would make prints quite crappy

2
Hash_KetchumOP•

Yes, filament diameter is set to 1.75mm thanks

2
roryjacobevans•

If you haven't done so already, measure the actual filament as well. The 1.75mm is merely nominal for a lot of manufacturers, they can end up being 1.70 or even lower. Also measure multiple points to get an average. You'll need digital calipers, a cheap ebay pair will do.

2
[deleted]•

[removed]

1
AutoModeratorMOD•

This post was removed as a part of our spam prevention mechanisms because you are posting from either a very new account or an account with negative karma. Please read the guidelines on reddiquette, self promotion, and spam. After your account is older than 2 hours or if you obtain positive karma, your posts will no longer be auto-removed.

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

1