Can't get video output from the B250 Mining Expert board
EDIT: I plugged in a beep speaker and got one continuous beep followed by two short beeps. According to the internet, this means that no memory was detected. I guess I'll need to try RAM that I know works on this board. I'll report back.
My RAM is included in the qualified vendor list for this board though: http://dlcdnet.asus.com/pub/ASUS/mb/LGA1151/PRIME_B250M-K/B250_2DIMM_memory_QVL_report_201712.pdf?_ga=2.155792307.96767390.1517038330-1000781555.1516160709
EDIT 2: I'm an idiot and didn't push the RAM completely in. Thank you to everyone who helped.
ORIGINAL POST:
I'm a software guy, not a hardware guy. I haven't built a desktop before and I'm worried I bent the pins on the cpu or something. On the other hand, everyone seems to have troubles with this board. I can get the board to power on, but I can't get it to output any video via HDMI (and I don't have DVI to test that).
- Mobo: B250 Mining Expert
- PSU: CORSAIR HXi Series HX850i 850W
- RAM: Kingston HyperX FURY Black 4GB 2133MHz DDR4 Non-ECC CL14 DIMM
- CPU: Intel BX80677G3930 7th Gen Celeron
- Testing Graphics Card: XFX AMD Radeon RX 570 4GB
- Other Testing Graphics Card: Gigabyte Radeon RX 570 4GB
- OS: Ubuntu Server on a USB
So I installed the CPU and one RAM stick into the DIMM_A1 slot. I connected the CPU to the motherboard and the 24 and 8 pin connectors on the motherboard to the PSU. Then I connected my HDMI TV via the HDMI port and my keyboard via a USB port.
I powered on the board by shorting the two pins with a screwdriver, but I don't get any video output.
I'm pretty sure it's not the TV. I also took a monitor from an active computer and used a VGA to HDMI adapter. Once I connect, the self-test goes off on the monitor and I get no output.
Throughout all of this, I don't hear any beeps. When the graphics card is plugged in, a blue light is on. The graphics card fans and the CPU fans spin.
I've tried:
-
Clearing the CMOS while the board is powered off (and also removing the battery and clearing it again). I know something happens because the next time I turn the board on it powers up then down then up again.
-
Connecting the graphics card to the x16 slot and also to the first x1 slot with a riser.
-
Connecting the HDMI cable to the graphics card.
-
Two different graphics cards.
-
Plugging in two RAM sticks instead of one.
-
Plugging in the USB with the OS on it.
I'm at a loss here. My next step will be trying the RAM and graphics cards in my main desktop. I get the same behavior from the system when the graphics cards aren't plugged in though, so I don't think they're having an effect.
I have another B250 Mining Expert that I can try, but if I screwed something up, I will probably do it again on the next board.
EDIT: I plugged in a chassis fan but it still doesn't work. I might get a motherboard diagnostic card.
Posted Jan 27, 2018, 7:32 PM UTC · edited
After powering up, does your keyboard caps lock key or num lock key light up when pressed? I assume you have the correct input source set on your tv as well. BTW... these are great power button
Good call. No, I get no blue light when I press the num lock key. I tested it on a regular computer and I do get the blue light.
The source is set to HDMI 1 and plugged into HDMI 1, yeah.
Thanks for the link! I just ordered some.
I just tested all of the USB ports and none of them give me a light on the keyboard.
I've got a PS2 keyboard that I can plug into my main computer and into my rig. When it gets power, for both computers, it flashes the three lights orange and then they go off. I can't type on the keyboard even on my regular computer though for some reason.