Pointers for Making Custom Titan Rockets with Pool Noodles

Currently I am working on a project by customizing a titan I picked up at my local war. It didnt come with any rockets so Ive been spitballing ideas for my own ammo.

Currently I have a pool noodle that I have cut into 8" sections that I will be mounting on 3/4" CPVC pipe with a connector to mount on the threading at the end of the tank.

My idea for the ammo (not yet tested) is to take the noodle sections, and cap them with half of a blue penn racquetball. This way I have a bit of weight at the tip for accuracy while still having a (relatively) soft impact that wont demolish my target. Im not sure of the proper adhesive but I was going to try some Gorilla glue.

If anyone has any pointers I'd be thankful for tips!

Posted Jun 13, 2018, 2:09 AM UTC

422
HockeyGuy32100•

Make test battle has a guide on making pool noodle titan rockets

6
-PowderCharge-OP•

I will definitely check that out! Lately ive been big on doing blind mods cause it reminds me of the days of racking my 13 year old brain thinking of ways to deal out foam death to opponents but this one has me stumped lol.

3
Kajimishima2•

Once I managed to make a few pool noodle rockets for the stock bore rather than mod the barrel. It was probably one of the smartest and dumbest methods I ever devised, but I've never shared it before. Definitely a case of harder not smarter, though.

I took an aluminum can and cut a strip from it then glued it to the removed Titan barrel. Then I twisted the barrel clockwise down the segment of pool noodle, boring out a section of the inside and making a noodle segment with an interior bore that fit snugly on to the Titan barrel. I used stress balls for the heads and craft foam for the fins.

All in all I was happy with the experiment. I could churn out 4 or 5 working rockets in about an hour and a half, and I didn't have to mod my Titan, but I really should have just modded my Titan. It was fun to play around with the different fin shapes and materials though. Some constructions had visibly higher spin than others.

I want to get back into rocket making, it was a lot of fun. Mine were even dyed black and had a yellow "CAUTION" stenciled on the side. But this time I think I'll just mod a Titan rather than rebore a pool noodle.

4
-PowderCharge-OP•

This is the EXACT thing I was looking for. I was thinking of using sheet metal to make a "cookie cutter" of sorts for boring the noodle but this is a way better application and easily done with a monster can. My threading on the adaptor to the 3/4 CPVC wont fit the titan without modification and I wanted something thatd work outside of using a heated rod to melt it or taking a filet knife to it. I will definitely give this a shot and see how it turns out.

2
-PowderCharge-OP•

One issue I am having is boring all the way through the noodle. Do you just kinda force it through in one go?

1
Kajimishima2•

No, I continually twisted it in one direction until I got all the way through

2
-PowderCharge-OP•

My aluminum jig keeps getting warped as it goes through or the foam begins to build up and jam up the process. I got one done but it feels a tad bit loose on the barrel. It might just take some practice.

1
-PowderCharge-OP•

Also, I have omitted all the extra bits that allow a scout and scorpion to mount the blaster, as well as the ball bearing safety so I can arc shots reliably. I have retained the power gague. This is going to be a pure titan build.

Edit: Sentence structure was off.

2
Messinger91•

You’re on the right track. You’ll want a thin sleeve of something like PETG on the inside of your rockets to better contain the air release and also so your rockets don’t explode from the sudden pressure. I really wouldn’t recommend using a racquetball as a rocket tip as they’re quite firm, instead perhaps a foam practice baseball or foam stress ball half.

2
-PowderCharge-OP•

Ill try a foam ball if I can find one. That was my first idea but after seeing what was available at my local stores I went with a racquetteball. (These things were mad fun playing wallball with and theyve got a decent weight) Ive got a prototype setting right now that Ill do some pain tests with once I get finished painting the shell. If it seems to be too rough Ill shop around for some softer foam. The bright side is at the very least Ill have rounds to use at home and private events. My idea is to have the ammo themed as well as the launcher itself!

1
LightningEagle14•

My noodles fit 1/2 pvc. Use something soft like a stress ball for the fins. Also- this is very important- be sure to spiral the fins, this will greatly improve the accuracy.

I don’t think adding a PETG sleeve inside is nessisary, but as I’ve never tried it I guess I shouldn’t have an opinion.

2
-PowderCharge-OP•

I figured there was a bit of discrepancy with the actual size of the noodles. My pool noodles have about a 2.5" outside diameter, and a 13/16" inside diameter. The CPVC im using has an outside diameter of 14/16" and an inside diameter of 11/16".

Really when I had bought all this I just checked the actual titan nozzle size to the noodle first, (the fat pool noodles costed more and seemed oversized) then afterwards I actually checked the plumbing section for some PVC that fit snug.

1/16" of free space was actually just pure luck because I only measured the actual dimensions as I wrote this post.

Make test battle (also just watched his video two seconds ago) mentioned the spiraled fins, I may replicate this, but with smaller fins because I want to have as close to a perfect cylendar as possible for the theme.

1
LightningEagle14•

Whoops I meant a stress ball for the tip. Noodles can vary a bit in ID. MTB used 3/4 pvc for their rockets. If you don't want to use a stressball you could roll up some craft foam and glue that in. Or, you could just duct tape over the front like I did. Mine don't shoot all that well though, might just be that the seal is crappy.

2
-PowderCharge-OP•

Nah I gotcha, seems like stress balls are the way to go. Ive been fiddling around wih my racquetball rocket and it shoots nicely (as nicely as a stock titan can shoot) but I am concerned with showing up and then having my blaster banned cause the ammo isnt up to par.

I might go with a weighted tip and duct tape, because performance isnt a huge issue in my case because I am including a little drop in sniper barrel to single it to an elite. (Last I checked this thing when singled still shoots under Caliburn FPS so rules be darned)

But the main theme is a blaster with custom projectiles. Form over function in this case.

1
LightningEagle14•

Caliburns can have different performance levels based on what spring is used, this is so you can adapt it to be used at your local superstock game.

Are you trying to enter this in a contest? I’m curious.

I don’t know anything about rocket science, and my knowledge of physics is limited at best, but I would say that weighting the tip probably isn’t necessary and that your only going to decrease range by making it heavier.

From my tests with paper bodied rockets the heavier they were the lower the ranges were.

2
rhino_aus•

One tip I have that I didn't get to put in the video I did was to make sure that the fins you have match the hand that the throw with. Anyone who's thrown an American football, cricket ball, baseball, etc knows that the what you fingers wrap around it imparts a spin.

I didn't consider this and put the fins in the opposite direction to my hand throw natural spin and now when I try to throw them without the Titan, they suuuuuuuuck

Other than that, check the my vid on it. The Tl:Dr of it is a reasonably length of noodle, an inch or two of broom handle for weight, a layer of foam yoga mat, then half a stress ball. I used thin craft foam for the fins, but would suggest you find the thickest possible for durability. I used contact adhesive to attach the parts

The yoga mat layer isn't suuuper necessary. If you do include it, you can use a knife to get the rough shape, then use a belt sander to smooth it down to match the noodle.

I sorta struggled with some of the noodles bursting from using too much pressure and making the cut slots for the fins too deep. I thought that maybe I could find a thin hard plastic insert that sleeves over whatever barrel material is use but I never ended up pursuing it.

2
-PowderCharge-OP•

The wood section weight is a pretty good idea because the main difference I noted between the racquetball and foam ball tips is the foam tipped rounds fishtail significantly more. (As per my hypothesis) having a bit more weight up front would probably help with this greatly.

As for the foam busting, my current ammo is actually wrapped in a snug layer of tape for security, and also because the texture of the base foam doesnt quite look right with the theme I am going for, sadly I also had to omit the fins for the sake of aesthetics but I think the brass barrel for accufakes and the overall theme will make up for the diminished accuracy.

1
rhino_aus•

100,000,000% put angled fins on your rockets my dude! It makes such and insane difference

1