Help choosing a compressor for car paint

I don't know if this is the right place, and let me know if I should post somewhere else. I want to repaint my car and practice on it (since it's a beater) before I try on the project car we plan on getting soon. I am broke and can't afford to spend much on a compressor.I probably will be doing panel by panel since I don't have a whole lot of time and have to drive the car daily. I have repainted my spoiler using elbow grease and sand paper and spray cans, but it's just not... the result I want, and doing a hood, or door would take way too long to do by hand. I also don't know how I am going to like repainting cars, so I need something for starter DIY.

I know I need HVLP. That's about it. Harbor freight, home depot, lowe's and local stores only (TX), if possible.

Bonus points on a compressor if I can use it on air tools(impact gun and all) and/or airbrush for finer details and other hobbies that requires painting.

Thank you so much for answering. I am lost with all the choices and prices and really need help. Google didn't help much and hope personal experience will be better!

Posted Jun 26, 2018, 3:42 PM UTC

715
im_not_a_grill•

Panel by panel is a bad idea because things like the air temperature can drastically change the shade of a color. If you spray one panel one day, it could be an entirely different shades the next just due to temp and humidity.

Watch a bunch of videos on YouTube. Just search "how to paint car cheap". That way you can see how a bunch of different people use a bunch of different ways to do the same thing: paint a car cheap.

5
Lyriel12OP•

Doesn't repainting all the car without removing panel create areas where the paint is weaker and could chip? The edges and the back sides wouldnt be painted either? I really want a compressor to avoid rattle cans.

1
ThatFordDude351•

I think what they was getting at was you don’t want to shoot different panels with different batches of paint on different days as it is very possible to get variations in the colors. The “proper” way to paint would be pulling all the panels off, then priming them all (panel and jambs) and mixing one large batch of color and painting everything with the same batch of paint with the same environmental conditions to get the most consistent coverage of the vehicle.

Plus it sucks to have to clean the gun 15 times through out painting the car. I’ve done it and am still doing it but I’d much rather blow the car apart and to paint all at once than one piece at a time.

Edit: yeah don’t waste color on the back side. Just around the edges if you stop at an edge there is a greater chance of delam.

6
im_not_a_grill•

This guy gets it.

Also you don't have to take the panels off if you're repainting the car the same color or close enough. If you're, say, changing a white car to a black one, you might want to take the panels off and spray the door jambs as well. The engine bay too if you're going serious business. But since OP mentioned they're broke, I imagine they're not going to take the engine out and repaint the engine bay.

6

Do you think the engine bay also depends somewhat on how cramped it is? I've got a grey Civic I'm contemplating painting white. It's not like a 72 Bonneville with lots of extra room. The interior barely shows up because it's so cramped.

1
im_not_a_grill•

Edges are inherently vulnerable areas regardless of if the car has been repainted or not. A brand new car's edges are just as vulnerable as a car that has been professionally repainted ten times.

Why would you bother painting the backside of a panel? It's already covered with a rust protection.

Then use a compressor. You'll need one that can keep up with a HLVP gun. So that means a bigger tank. The bigger the tank, the longer you can spray before you need to wait for the compressor to catch up.

All air compressors can be used with air tools. You might have to change the ends out (not common) but they're all pretty universal. Again, the bigger the tank, the longer you can use your tools before you have to wait for the compressor to catch up.

1
PsychoEngineer•

Well, my answer here is probably not what you're going to want to hear.

Painting a car at home is not cheap if you want good results. Equipment alone will be at bare minimum several hundred, then easily that in supplies, plus another several in paint. Basically on the cheapest end to get a 10' paint job at home is gonna be a grand.

Now if you want a 1' paint job, you're looking at more like 1k minimum in just equipment, then at least another k in materials and paint.

Equipment wise, a 60G 6hp compressor from Lowes/HD will work, anything smaller you can use but will not support continuous painting which makes keeping a wet edge harder. HF HVLP guns are ok, especially for primer or sealer; they are eh for color/clear. I use a DeVilbiss set of guns myself, but the Eastwood ones are a good budget alternate for color/clear. Also going to need some form of dryer, disposable ones work ok; I use a disposable at the gun, and a DeVillbiss AC3 on the wall.

Paint wise, I'm a PPG guy or Sikkens; I'll use HOC but only for crazy stuff I can't get from anywhere else due to the cost. I have heard good things about Napa and Eastwood paints but haven't used them.

3
Jehannum_505'67 GTO, '71 240Z, '92 300ZX, '90 Cadillac•

Based on looks and reviews, I assume the Eastwood guns are the same as the HF and kobalt. I've only had firsthand experience with the Kobalt, which I hated (inconsistent pattern and bad atomization).

I agree on the Devilbiss recommendation. Between the DB FinishLine and the Sharpe (fx3000), I ended up with a product I was pleased with.

1
PsychoEngineer•

Eastwood from what I found online are private labeled DeVilbiss guns.

I have 4 FL4 guns that I use for painting; all dedicated for their use. 1 for clears, 1 for colors, 1 epoxies, and 1 primers. You can get away with 2 guns, but I found a killer sale and 4 makes it easier IMO.

2
bse50'91 Miata - Westfield Megabusa . GTB Turbo•

You need AT LEAST a 100l oilless compressor to do a proper job, plus a bunch of filters, traps and desiccants.
A dust-less and properly illuminated / ventilated / thermoregulated paint booth to work in will still make a huge difference.

2
PsychoEngineer•

The paint equipment I'll agree with, but I've painted cars that turned out flawless with a home-made spraybooth made from plastic sheeting, some furnace filters, and a couple box fans. But you do have to pick the right day temp/humidity wise to spray.

2
devilpants•

My experience from painting my own engine bay "properly" was to never do it again. I had a large compressor already and a ton of tools. By the time you get all the materials together, get a proper gun, traps, clean your space from dust, prep, do research, buy all the paint and then still get orange peel and have "ok" results because you don't do this every day.. you are better off prepping everything super well and then dropping it off at a paint shop, even a super cheap one. They have a booth with no dust and a proper gun and materials and the guy that's shooting it even if he sucks is probably going to be better than you on your first or second try. You'll probably end up spending about the same too.

The key is all the prep. If you do that yourself and take it almost anywhere you will get ok results.

1
scott_fx•

The guys who I use for some of my stuff (they work on $100k+ cars for the owner of New Balance) have a similar mindset. Well... they do their own body work and paint. But they have told me that if you do all the prep and take it to maaco... you’ll get a very good end result. The maaco guy paints day in and day out. He has plenty of practice they just cut corners on prep since they are about quantity

2
someonestopthatman•

Buy the biggest compressor you can afford. You'll want it later down the road when you're doing project car stuff.

For a gun, the concours stuff from Eastwood is OK. Not great, but with some skill and GOOD prep I've gotten decent results with it.

You'll also want some kind of dryer ilter on your air hose. I use one at the compressor outlet and a disposable one at the gun itself.

Paint is expensive, but you don't need to spend a billion dollars on ppg. The mid-line Napa stuff is ok. Nason makes ok paint and their overall clear is actually pretty good, without breaking the bank.

The key to a good job is prep and cleanliness.

If you're going to do your beater panel by panel, buy all your color at once. If you don't you'll really notice the difference in shade. It still won't be perfect if you don't do it all on one day,but should be good enough for a beater car.

There are a million videos on YouTube about painting cars. Watch some of the Eastwood ones, they're pretty good.

2
I-r-machinist•

What's your budget?

I've sprayed with the HF 21 gallon standup compressor, as well as light air tool use and some minor sandblasting. They go on sale ~150 from time to time.

1
BiggRanger3.8L powered sand rail•

You will want an air dryer for your compressed air. My original air dryer was a 2 foot long 3" PVC pipe filled with desiccant that the air was forced through. I kept the pressure around 60 PSI and the thing in a metal box in case it exploded (it made me a little paranoid), and ran a particle filter after it. I've since replaced that with a Craig's List find refrigerated air dryer that needed a little fixing up and new filters.

1
CruxOp•

I wouldn't go anything smaller than 60 gallons if you're looking to do actual work and not be stopping all the time. I had the 21 gallon Harbor Freight compressor and after six months gave it away to a family member and bought the 60 gallon one from Lowe's and haven't looked back. The problem is the 21 gallon has a max of 120 PSI. Remember HVLP stands for high volume low pressure, so you want to make sure that you have enough volume in the tank and duty cycle to actually be able to paint without stopping constantly. Air compressors are one of those things that you should bite the bullet and spend a few more bucks on the beginning and then not have to upgrade it again.

1
Jehannum_505'67 GTO, '71 240Z, '92 300ZX, '90 Cadillac•

If you've got one of the cheap guns from Hazard Fraught or Lowe's you're going to need a lot more pressure (and volume) than some of the better guns. I've used sharpe, devilbiss, and kobalt. The sharpe and devilbiss both worked best around 25-30 PSI, while the kobalt sucked unless you jacked it up to 60 PSI. PSI ratings aren't super important, but the benefit of HVLP is that you can more easily control the amount of paint flowing, and at 60 PSI that becomes a less tenable proposition.

I've done panels with a smaller compressor (a "2" horsepower 30 gallon oilless craftsman), which will work for panel to panel jobs, but end up kinda sucking for anything more than spot work. I really love my Napa 5HP 230V 80 gallon, and won't work with anything less, now that I know what I was missing.

You'll also need some manner of dessicant and filtering. A simple catch can on the compressor outlet is all I personally use, as it's a rare day when my ambient humidity is over 10%.

1