Can I hook any USB C phone to my dash charger?
I'm afraid of frying my friend's phones in case they can't handle the extra power.
Posted Jul 27, 2018, 8:00 AM UTC
I'm afraid of frying my friend's phones in case they can't handle the extra power.
Posted Jul 27, 2018, 8:00 AM UTC
It will work great. It will steadily charge at 5V/2A. This will charge a 4000mA battery in about 2h.
Thanks a lot!
No problem. Just for the sake of providing a bit more info:
for electrical devices, you usually need to provide the (V)oltage (aka tension) the device is expecting to work. This is the value that will fuck stuff up if it's not the right one. Quick charge is a bit of an exception because it's made especially so it can take varying voltage (more info below) but it's something that in general you want to provide the specified amount with little variation.
the (A)mperage (aka current) is more like "drawn by" and not "provided to" the recieving device. So the reciving device will only take what it needs, you can't accidentally give it more, even if the charger is rated for way higher. It just means the charger could stand to provide more if the device needed to. It's the same when we install 700 or 1000w power supply units on our desktop PCs, very rarely the pc will actually use that much but the room to do so is there.
Potency ("power") provided is calculated by P = V x A meaning if you want to provide faster charging (increasing P), manufacturers increase either V or A or both. For charging batteries, due to lithium battery tech, they usually make it charge a ton faster initially but a lot slower when it's nearly done.
There are mostly 2 fast charging methods for phones at the moment: qualcomms standard quick charge that almost everything uses (and some wildcard variants of fhis) and dash from OnePlus. QC uses varying voltage up to around 20v and slowly lower and adjust down until the phone is charged. Dash is the opposite, will always charge at 5V but on supported devices will pump amperage to nearly 4A and will slowly lower that until charged. Since every phone was made to be plugged to a USB port (which run at 5V) it's safe to consider every phone can be plugged to a 5v source. Well, the OnePlus dash brick literally can never give more that 5 because that's how it works so there's no chance it will burn any other phone.
cable length and thickness mater. OnePlus way needs a thicker cable, which is usually shorter. QC way isnt as restrictive, pretty much any cable, as long as it's not total shit will do.
Don't forget USB-PD, which is similar to (but not compatible) QC, except it uses voltage steps instead of QC's varying increase. This is what Google is pushing on with and a lot of other devices (eg laptops, etc) also supports. QC 4 is compatible with USB-PD though but there's only a very tiny amount of phones/chargers that supports it.
Whoa, thank you for taking the time to type out that explanation. Electrical power makes a lot more sense now.
2h is about correct without any efficiency loss. It's closer to 2,5h if we assume around 20% is lost to heat.
If no loss then 522= 20Ah, not the 4Ah quoted.
Well, so far I charged a Nexus 6P and a Nexus 5X and it worked without an issue.
Great to know, thanks.
do you use the dash cable also? should be fine right?
Yes, I used the dash cable. It was fine in my case.
I can not charge my Old 6P and my mom's s8 with my dash charge adapter or cable.
Does anyone know if it's the plug or the cable or both that are needed for dash charging? for example, if I lose the cable can I put use any type C cable and plug into the dash charger and will it still provide dash charging?
Seems to need both.
[removed]
I experienced that most devices working good. Like Huawei phone are charging pretty fast with the dash charger. Don't know why. Some Samsung Phones (like the A5 2017) are not charging overall.
Tried it with my Nintendo Switch and, interestingly enough, it didn't provide enough amps to charge it. Could well be Switch-specific, though.
I've read about a lot of issues regarding the Switch and its charger interacting with other devices (either charging the Switch with another charger, or charging something else with the Switch charger). I think it's because the switch charger is hardwired to pump out 15v or something.
Ah I see. I mean, a regular phone charger (1amp) worked fine for some reason. Odd.
[deleted]
Anybody know if it's safe to use my Chromebook USB-C charger to charge my OP6? My guess is that it will be fine, but charge slowly (no dash charging), but I'm reluctant to try!
Yes you can.