Does this look like a healthy fermentation of a Hefeweizen

I've started brewing a Hefeweizen about a week and a half ago. I checked on it and it looks like this and bubbling stopped after the third day or so. Does this look healthy? I've brewed some before and they've had more stuff on the top (krausen?) And stuck to the sides. Also this seems so much darker than any Hefeweizen that I've ever seen. Picture of the fermenting beer

Posted Aug 31, 2018, 11:53 PM UTC

411
chino_brewsKiwi Approved•

Looks good and nearly done. The hydrometer is sitting low, telling me gravity is low.

The yeast are probably still in suspension preparing to drop out and go into a quiescent period. Give it a few more days at around room temp. The color can be deceiving because you're looking through a lot of beer without light passing through the beer to your eyes. It will likely look paler when passing directly through a few inches of beer in a glass.

What does that hydrometer read?

Don't take hydrometer readings in the bucket. Besides the risk of contaminating the whole batch, you can't read it at eye level like you're supposed to. Also, if you leave it in the bucket, kraeusen can stick to it and throw off readings.

3
bhuff85•

As for fermentation, it looks normal to me. If it's been 1 1/2 weeks, the krausen has dropped. Pretty normal for that to occur after fermentation is complete.

On the color, yeah, that looks more akin to a Dunkel Weiss. What was your grain bill? That might help zero in as to why it's so dark.

1
SlowBenOP•
1
AyekerambA•

I wouldn't fret about the color. You did a partial boil and added the LME at the beginning which causes a fair amount of caramelization because you have a lot of sugar condensed into a small amount of liquid.

In the future, you can add your LME to the last 10m of the boil, but you'll have to up your hops by 10-20% to hit your IBUs.

2
bhuff85•

Thanks!

While I know that extract beers are usually darker in color when compared to their all-grain counterparts, I wouldn't think it would be that dark. Only thing I can think of is a lower water volume may have been used and there was more boil off than intended, which would concentrate the wort and darken things up. If that was the case though, your OG would've been higher than the recipe's estimated 1.046 (not sure what your actual OG was).

As I mentioned before, the fermentation looks fine and you don't have anything to worry about there.

Have you pulled a sample to taste yet, just to see what flavors you're getting? The good thing is beer is usually very forgiving, so there's a good chance you'll most likely end up with a drinkable product regardless of color or other nuances.

1
goinTurbo•

What's your gravity at and what's your target gravity? Also what is the temperature?

1
SlowBenOP•

I think I may have messed up my hydrometer because it says my gravity is like 1.007 and my target is 1.012. I was shaking it (like a shake weight) and I think the paper inside was moving. The temperature has been a shit show. My apartment has been fluctuating a lot for various reasons but I've been trying to keep it relatively warm because I heard it gives it that banana clove flavor

1
chino_brewsKiwi Approved•

I was shaking it (like a shake weight) and I think the paper inside was moving.

Yeah, test it in 60°F water when you're done. You're supposed to treat it like a very sensitive scientific instrument made of very thin, brittle glass, not like a shake weight!

1.007 seems low for this beer.

1
seafoodslut1988•

My hefe looked that color am came out normal, bet it’s just fine 👌🏽

1
SlowBenOP•

Ok man. Thanks for the reassurance

1
seafoodslut1988•

For sure. Here’s a pic of mine. It’s the one on the top left. Hefeweizen

1