Help Please! Using Conduit to bring wire into a wall properly [King County/WA area]

I have a garage where, for some reason, they finished it, and decided fuck it, who needs electrical outlets on the wall in the garage, especially near the work space area.* A long time ago, they clearly finished the upstairs and ran electrical to the panel by putting a junction box about 1/3rd of the way away from the wall on the ceiling, then running conduit to the panel by going across the ceiling, down the wall, then cutting into the drywall above the panel, and attaching the conduit at the top of the panel.

What i'd like to do, is put a conduit run into the other side of the existing junction box on the ceiling in the garage, and run that straight into the opposite wall, and put in some outlets on a separate (new) 20 amp circuit - I don't want to tie in to an existing breaker/circuit that's already in the junction box. I'd like to avoid having the conduit run vertically down the wall from the ceiling and have surface mount electrical boxes, so my question is, how do I secure the conduit to the wall on the far side and get the wire into the wall safely/properly/to code? I'm worried that the conduit would shift or something and push into the drywall gap if i just drill a hole and 'set' it there. (it's going to an interior wall, FWIW). I am operating under the assumption i need to check that the existing conduit has enough space for another run of the properly rated conduit wire for a 20amp circuit.

Other feedback appreciated as well if my approach is so fucked.

*In all fairness, they have single-gang outlets wired in the roof for the garage door openers.

Posted Dec 26, 2018, 11:17 PM UTC

18
CascadeCoconutCrab•

You're on the right track with verifying that the existing conduit is large enough to take a few more wires. Good on ya.

So, first a question. How far is it from the existing j-box to the wall you're looking to penetrate?

Next, a suggestion. Are you familiar with type MC cable? Flexible and versatile like Romex but with an armored jacket that protects like a conduit! This might be a better option for you than conduit. The downsides of MC are the mess it will make on your gloves/hands, you need special connectors to terminate the cable after you "strip" the armor off, it's easiest to use when you are using metallic boxes rather than plastic.

Get back to me and I will be glad to help further.

2
SixSpeedDriverOP•

I responded to the wrong person here. Editing to fix...

Not familiar with Type MC cable at all; I think for consistencies sake, I'd rather have conduit for the run (despite my misgivings about how the previous runs were done, I'm not trying to fix it ;) ). To wit:

Here's the view of the existing conduit/jbox on the cieling: https://drive.google.com/file/d/1dC9vv9FE3cCcORRH-_UW_zxlHHoCNEH_/view?usp=sharing

Ugly, but already there.

Here's the run I want to make across the cieling, and the wall i want the wire to go in to. https://drive.google.com/file/d/1xa4f0hkMmqY4O7L3FJtZrsZtAgpIPMVH/view?usp=sharing

As you can see, there is already a ghetto rigged heavy duty extension cord running that needs to go bye-bye. The shelving unit is blocking a small 24U telecom server rack I've got wall mounted up high with a 4U server , UPS, and switch/router shelf that I want to power more correctly with the high mount electrical outlet.

1
CascadeCoconutCrab•

Hmm... Honestly i think you're best bet would be to run Romex in ½" flexible metallic conduit to a second junction box. From that box you can just run Romex out the back, into the wall and to where you need it.

1
SixSpeedDriverOP•

Commenting to add, I searched the forum, and saw this thread, but didn't seem to have a good answer, I think we're both asking the same thing. https://www.reddit.com/r/electrical/comments/6yfq1r/best_way_to_terminate_conduit_run_into_drywall/

1
Phydoux•

It sounds like they are wanting to add a whole new run.

We need a little more info about your setup. How big is the conduit that's already there? 1/2", 3/4", 1"? Also, how many wires are in that pipe now and what size wire is it?

With that info we can help you better. Certainly if it's 3/4" conduit with only 1 run in it then you're probably ok adding another circuit in there.

It's hard to picture what you're trying to do with new conduit. If there is sheet rock there then you can drop the wire from the ceiling behind the sheetrock. Put the hole where you want your outlet to go and it's a little tricky but you'll have to get your hand in there and feel around for the wire. When you find it, pull it out of the hole and put your box in.

2
SixSpeedDriverOP•

Correct, a whole new run.

Here's what the junction box looks like and how it was tied into the panel: https://drive.google.com/file/d/1dC9vv9FE3cCcORRH-_UW_zxlHHoCNEH_/view?usp=sharing

Here's the shot down the other direction where i want the conduit to go into the wall facing you: https://drive.google.com/file/d/1xa4f0hkMmqY4O7L3FJtZrsZtAgpIPMVH/view?usp=sharing

I want the conduit to go across the cieling, then enter into the drywall, and have the wire run through the wall to a single-gang outlet pair high and two outlet pairs in a double gang box at about the height of the shop table not shown.

Is that kosher for code, do i need to terminate into a box up high inside the drywall or something? Ultimately, i'm going to buy a fish tape to make this happen, but I don't want to tear up too much drywall.

Thanks in advance for your thoughts! Haven't checked how big the conduit is, but let's run under the assumption the existing one can take another run :)

1
Phydoux•

I think you can run the pipe right into the wall. Some of the code pros should answer that one. What I would do, I would run conduit to a 1900 box (4x4 box) mounted on the wall. Have a hole knocked out in the back of the box and just take a screwdriver and punch out a hole in the sheetrock with a screwdriver where you put the hole in the box. Then feed the wires in the hole. Again, there may be something simpler to do bit that's the way I would do it.

1
SixSpeedDriverOP•

Yah, hoping a code guy can pop in on this idea, it sounds good to me; I do plan on selling in 3 years and don't want to create a future issue :)

The quote for this run and termination was $800. And another $400 to wire a light to the end of an existing switched run. And I have to hire a drywall guy to fix the wall if I don't want the latter run done in conduit.

1