2001 R1 rough feeling and sounding midrange

Solved

Hey fellas, hoping someone here has insight to offer as I can't put my finger on what this is.

The bike rides beautifully smooth from 0-4000 rpm, but between 4 and 7k it gets very rough, very snarly. It's difficult to describe the feeling but it's almost like fuel starvation without a significant loss in power.

Valves are in spec and plugs are relatively new. I'm wondering if it might be poorly jetted carbs but I have next to no performance carb experience so idk.

Thanks in advance!

Posted Jan 11, 2019, 1:45 PM UTC

813
HackedVirus•

Has it sat for any period of time? When was the last time the carbs were removed and throughly cleaned?

2
MaybeNotHeteroOP'01 R1 // VFR 800 Streetfighter•

It has not sat for any period of time, I've never removed the carbs for cleaning but they've never exhibited any other signs of being gummed up. Starts easily and the pilot circuit runs fine.

2
HackedVirus•

Have you attempted using a fuel cleaner to try and clean the carbs without removing them? And is the issue only when you're riding, Does it rev properly in neutral?

2
howd_you_find_me•

What is a good product to use for this? I have a similar issue on my 2002 zx6r when applying very little throttle to just maintain cruising speed.

2
HackedVirus•

Well i know some people love seafoam but i was always recommended B12 Chemtool and it seems to help my old bikes if i suspected there was some buildup in the carbs, your mileage may vary but i usually say B12, its pretty cheap too and you can find it at advanced, walmart etc. Another thing to check are that your butterfly valves are synced properly

1
MaybeNotHeteroOP'01 R1 // VFR 800 Streetfighter•

I've used carb cleaner spray in the intakes but no fuel additives yet. Can't seem to get the same ones in Australia as in the rest of the world. Not easily at least.

2
HackedVirus•

Well I'm sure any fuel additive that claims it cleans fuel systems and carbs will do the trick. Do a little research online for your part of the world, though I always recommend just ripping then out and doing a nice full cleaning, but that's me, I enjoy ripping bikes apart and fixing them. Ripped the carbs put of my GPz1100 atleast 10 times while I owned it until I finally did a deep clean and soaked it in boiling water, never had an issue afterward, let us know if it helps, if you can rule out the carbs as being the issue it narrows it down big time. Maybe even check the resistances on your ignition coils as well, not sure how many your bike has exactly

1

Maybe raise the needles with a washer or clip position change. Any air filter or exhaust changes?

1
MaybeNotHeteroOP'01 R1 // VFR 800 Streetfighter•

Stock filter, Yoshi slip on. I'll give that a shot, thanks!

1
JDSportsterHarleys, lots of them.•

There's a saying; 99% of carb problems are electrical.

Any mods on your bike that would make the stock jetting and needles not work for some reason? Has it always done this?

1
MaybeNotHeteroOP'01 R1 // VFR 800 Streetfighter•

Only had it for ~6 months. It has always been a little rough. Only mods are Yoshi slip on and quickshifter.

1
Caldtek•

What is the mileage? Ive seen this symptom on high mileage bikes (50K +) caused by worn needles and needle holders in the carbs. If they are clean, everything else is in good order, that would be my next item on the list.

1
MaybeNotHeteroOP'01 R1 // VFR 800 Streetfighter•

40,000 KMs, that's an interesting suggestion that I haven't heard before. I'll look more into that, cheers!

1