r/ender3•
DeepReally

Thinking about getting an Ender-3

I'm thinking about getting an Ender-3. Are there any 'essential' mods I should get at the same time? I've read something about a bowden clip(?) and better springs being good initial mods. Does this sub have any opinions on things to mod before first use or is the out of the box experience okay?

Posted Feb 5, 2019, 2:08 PM UTC

214

I was out of box for a few months, the only upgrade I've purchased was a glass bed. All the rest are printed upgrades.

3
pete8081•

Only essential thing I could say is to get a mirror or glass print bed.

Other wise, upgraded springs, Bowden tube / fittings, and printed filament guides are nice to have.

3
Thatretroaussie•

Out of the box it's fantastic but, yes there are some Essential mods for it. Nowhere near as many or as "critical" as mods for prusa i3 clones but, needed none the less.

Bowden clips can just be printed or made with some spare wire.

Replacing the springs is a cool upgrade, as they're reported to be easier to calibrate beds but, tbh the springs that came with it, work fine for me.

But here's my recommended Essential mods. #1 Mod your extruder filament feed frame.

The stock filament feeder that comes with it, is made out of plastic, so as the extruder pulls the filament, it just grinds away and causes this to happen so you have two choices. You could either buy a metal version of it eBay link or, you can do what I did. I used the spare coupler that came with the ender 3, drilled a hole into the feeder and then just screwed the coupler into it and used a mount on the back so it wouldn't hit the z screw rod. #2 Get a glass bed. The flexible bed that came with the ender 3 absolutely shit. Having a flex bed sounds good in theory but, in pratice (atleast for me) it was just a pain in the ass to deal with. #3 Get one of these Trust me, it's so much easier having this. If you take out the sd card alot, this is a godsend. #4 Print this filament spool adapter. Unless you're using a spool that has a small hole this print is a must have. Basically because the hole on most rolls are much bigger than the size of the spool holder, instead of smoothly rolling as the filament extrudes, it skips. It doing that could cause some issues with extrusion and print qualilty. #5 (This is entirely optional but, trust me it's a good tip) Get a roll of black filament for upgrade parts. Trust me, it looks so much better to have printed parts match the colour of the ender 3, than just having be in a clashing colour

3
Sfillm07•

I bought a $12 inductive sensor and wired it to my board for auto bed leveling, probably my favorite mod so far.

2
DeepReallyOP•

Was that the BLTouch or a different model?

1
D4RX_•

At 12$ it's definitely not the BLtouch, also the BLtouch isn't inductive.

1
sKKKc•

Go for it

2
Dweller•

Must have (IMO): Glass bed, upgraded springs, printed fan cover, filament guides.

Nice to have: cable chain, enclosure, Octopi (rasberry pi running Octoprint), firmware upgrade to enable things like mesh leveling and thermal runaway protection.

OMG Why did I not do this sooner: BLTouch. By far the trickiest of the upgrades but well worth it. If you have done the firmware upgrade then you are past most of the tricky part of the install.

2
Shdwdrgn•

If you get the Ender 3 (not needed for the Pro), print the fan cover as soon as you get your bed level, followed immediately by filament guides.

There are clips that come with the Ender for the bowden tubes. These are really just bandaids for the poor quality fittings that come with the machine. Likewise, the extruder head is low quality, but both of these will work for awhile. Get yourself the aluminum extruder head and a package of new PTFE tubing (should be 4mm OD and 2mm ID) that comes with 6mm and 10mm fittings.

If your bed is warped (and they almost always are), a glass bed will help, but not completely fix the problem. If you have some calipers on hand you can get the corners as close to each other as possible, then use foil circles to shim up the center of the bed to match the corners.

Bed leveling is essential but can be tricky to get it just right. It takes time to learn the process but is well worth taking the time to do it right. The upgraded springs are probably nice but the stock ones have been working fine for me for the past two weeks.

If you don't want to tie up your computer during print jobs, install Octoprint on a raspberry pi. It can provide a variety of features that make it easier to use your printer, including remote monitoring through a web cam.

2
DeepReallyOP•

Ordered an Ender-3 with Glass Bed and replacement bowden tube/connectors. Will look at upgrading springs and extruding in the next month or so.

Thanks for all your help!

1
othybear•

The springs are only a couple bucks. I'd recommend getting them now and installing them when you do your set up.

1
DeepReallyOP•

The springs are only a couple bucks. I'd recommend getting them now and installing them when you do your set up.

Got a source for them, because on Amazon.co.uk they were like £12 or something.

1
othybear•

These were only $3 when I ordered them, but they're up to $7.50 now.

1
Sfillm07•

I bought a generic one from Amazon. Took 24v from the board and used a voltage divider on the signal wire to bring it back down to 5v.

This guide was a good starting point for me.

This video is a little outdated but does a good job explaining the process for getting everything calibrated.

1