Leaning Garage, In Need of Ideas!
[removed]
Posted Apr 10, 2019, 10:50 PM UTC
[removed]
Posted Apr 10, 2019, 10:50 PM UTC
I am seeing wood rot, worn out shingles and of course major structural problems. By the time you fix it up, you'll probably wish you had it torn down and rebuilt.
Thanks for the response. You're right, it's old and does need to be rebuilt. Unfortunately that's not affordable at the moment.
Okay, here's how you do it.
Since it's leaning towards the front, you will need to pull it from the back, obviously.
Hopefully there is a giant tree back there you can use as an anchor, if not you'll need to park something heavy like a truck to use as a fixed point.
Next you'll get a couple of 2x6 or 2x8 boards as wide as the back of the garage, and you'll put one on the outside and one on the inside horizontally so they are sandwiching all the studs between them. Use a couple long carriage bolts to secure them to each other. Then screw the inside one to each one of the studs. You are making this a giant sandwich clamp so you can pull all of the studs backwards simultaneously. Put it as high up on the wall as you can, at least six feet up.
Put a big eyebolt on each end of the outside board. Get a steel cable and make a big loop between the two eyebolts.
Now attach your ratcheting come-along between the anchor point (the tree or the truck) and the steel loop cable. Slowly ratchet the building back to plumb. You need people on the inside and on the outside watching to make sure nothing is cracking or breaking or falling down, and work VERY slowly. Give the building time to adjust between each click of the ratchet. Not an hour, but maybe a minute or so between each click. If things start to act wonky, it gives you time to reassess what you are doing so you don't make things worse.
Once you get it back to plumb, you'll need to put lots of diagonal reinforcement on the side walls of the garage, attached to all the studs. There was probably diagonals there sometime in the past that were removed, hence the problem you are having today. You can use 2x4's, you don't have to use metal straps, but you could if you wanted to.
Good luck and send us some pics when you get it repaired.
7/16" OSB sheathing attached to the studs would give more bang for the buck for a DIYer. I would suggest one sheet per corner, and the sheets must be nailed with 8d common. That should be less than $10/sheet
That is probably true, plus it gives the appearance of a finished wall, and makes it easier to hang shelves and brackets and such. But, on the other hand, it's much more work. You can do one diagonal 2x4 for 10 bucks and be done with it in five minutes, but you might have to use four or eight sheets of OSB and be done with it in two hours after you cut out all the holes for the existing electrical outlets, etc. So it's sort of a tradeoff.
Thank you so much for your time and guidence. I wasn't sure if it would even be possible to straiten it out! I will check around and see if I can rent a come-a-along (one each side). Unfortunately the back of my garage is against the property line and a fence. I am thinking I could go from the front near the top sill plate down to the back bottom and get ahold of the foundation wall. I am thinking that should be solid enough? Not sure how much Force it will take to pull it back. Will definitely post after pics. Thanks again!
Well, you could try to do it like the guy did in that video, but it's more difficult as you need two come alongs, one for each side. You can get come alongs for about $30 each at Home Depot/Lowes.
It doesn't take much force to pull it back, just make sure it's anchored strongly.
Is it still correct left to right? I couldn't tell from the pics.
If it's leaning left to right also, then you would need to correct the front to back lean, and then switch the come alongs around so you could correct the left/right lean.
Like the inspector mentioned that roof looks shoddy but if the framing looks fine I would try to box it out with diagonals after pulling it straight. Probably could use those existing boards in your rafters and pull it back via the back windows with a rachet strap as described.
Where is this located that there are no windows enclosing your garage?
Personally I’d try and remove the tiles and that way building is lighter and less likely to fall back and damage rotting wood, then straighten out and use either long planks angled 45 to reinforce the structure from inside or place plywood against the walls and screw/nail in. You can skip the tile removal but make sure you brace the structure so it doesn’t fall back and weaken it further.
Your submission has been removed for one or more of the following reason(s):
We want you to get the help you're looking for. If you have any of these questions, here are some places you can get that help:
Please read our guidelines before resubmitting.
If you believe this was a mistake, please message the moderators.
###Do not respond to this comment - you will not receive a response.
That looks like a major structural defect? Unless I'm seeing it wrong, you should stop using it and have a professional look at that.