Fists runs

So I finally got around to finishing the still I half started about a year ago. Got a couple 4 gallon buckets of sugar head to about 10%. Ran each through, collected low wines and put it all back in with a bit of leftover wash to make sure I had enough liquid volume to keep my heating element submerged. I am now left with just under 5 litres reading about 45%. It is definitely rough stuff right now. I keep one bottle out of the center of the run and even mixed it has some kinda bite to it. I understand this is fairly normal, it is fresh, raw spirit that couple probably stand some redistilling, ageing, etc. Mostly just pleased with myself for making the thing work. About to try some of it mixed with something to see if it doesn't improve a touch not being north of 100 proof

Posted May 4, 2019, 2:23 PM UTC

1015
MyFireWaterAccount•

Let's see the new rig!

2
RiotForChangeOP•

The new rig is definitely ugly and not best practices. But like, it cost me probably 40 bucks after metal that was already lying around here so that's sweet

1

Why did you use the left over wash in the spirit run instead of just adding more clean water?

1
RiotForChangeOP•

Mostly because it was handy and largely clean and still a couple litres at relevant alcohol

1

If is still had relevant alcohol you could have run the striping run a little longer. I wouldn’t want to risk off flavors by mixing.

I usually save the extra mash for the next time I do a stripping run. Maybe what you are doing is okay. I just never did that.

2
RiotForChangeOP•

It wasn't stuff that had already been run, it was fermented wash still in the bucket that wouldn't fit in the still. Everything I got out last night is going to end up back in the still to clean up so I wasn't super worried about what how it came out. I knew the first real attempt probably wasn't gonna be great and would need some further refinement. Just figured I may as well get the extra bit of alcohol out while I needed spare liquid anyway and still had a few litres of overshoot in a fermenting bucket

1
RiotForChangeOP•

It's definitely not near as rough watered down some. And actually pretty decent in doctor pepper. Calling it a win for a first experiment making real rough cuts

1
theCaitiff•

Did you do a sacrificial run first? If not, that would definitely cause your firstrun to be more rough around the edges.

Also, you're leaving a lot on the table there. You'll never get 100% recovery, but if you only got 5L of product from 8 gallons, I'd say there is stuff you're leaving behind.

1
RiotForChangeOP•

I did do sacrificial runs, both vinegar and alcohol about a week before hand. What do you generally get for recovery, just as a curiosity?

1
theCaitiff•

If I'm using good yeast, keeping my temps steady, and am not too picky with cuts (easier when you have good yeast and temps) I can recover 5 gallons/19L of 70% from 30 gallons of 14% wash after a stripping and spirit run. That's ~85% efficiency from a 24" packed column running in pot still mode.

Comes out to damn near $0.60 per bottle for plain old sugar shine. Toss it on oak and it's an alright rum. Through in some juniper, coriander, and orange peel, then redistill and you've got odin's gin which ain't bad. Or use it as a liqueur base.

Again, that's broad cuts because I want something cheap to drink and mix. Better than some of the common brands of light rum but maybe not specialty brand quality. Casual drinking stuff not fine sipping whiskey. If I were making a whiskey meant to age then yeah my recovery would go down, probably significantly.

1
RiotForChangeOP•

Probably should have e run it further then. Gonna put another 8 gallons down to ferment in the next week or so, figure I'm just gonna add what I have back into that spirit run and see what I can't get out now that I'm a bit more used to how the still runs

1
theCaitiff•

On your stripping run, just go all out and get every drop. Use fresh clean water to dilute the low wines if needed and send it all back through in the spirit run. I don't care about heads or tails on the stripping run.

I don't know how your still is set up, but I can tell you a bit about my own. Simple beer keg with a 24" column out the top that I pack with copper scrubbers. This provides a fair bit of passive reflux if I don't insulate the column, but it runs faster if I do. Above that I can either turn 90 and go straight to the condenser for a pot still or drop in a reflux condenser then the takeoff.

I fire mine electrically now, just wrapped the keg in nichrome wire and hooked it up to a PID switch. Coil comes on and uses about 1500W to heat the keg to 99C, then turns off. Takes about nine hours to run a full keg this way but it's pretty hands off.

I credit most of my success lately to the "low" wattage of my heating element compared to my boiler size. When I was new and fresh to the hobby I used propane and had wicked smearing. Then I "upgraded" to a 220V 5.5kW element and burned things to the element constantly. I've been getting much better results and more of it since I swapped to the lower power and moved the element outside the keg. The lower power, passive reflux, and slower run concentrate the heads and tails more allowing me to extract more of those hearts we're all after.

1
[deleted]•

[deleted]

1