r/Coffee•
-jcs

Height of pour?

Real quick question. Hario V60 is my main brewing method. I have heard some mentions of it on this sub, but I'm curious as to how the height of the pour affects coffee. I'd imagine of it's anything noticeable it has something to do with agitation but I'm not entirely sure. Any answers would be greatly appreciated. Thanks in advance

Posted Aug 2, 2019, 10:06 AM UTC

813
VoteLobsterV60•

I'd imagine of it's anything noticeable it has something to do with agitation but I'm not entirely sure.

You're right. A higher pour introduces turbulence and more kinetic energy into the slurry making for quicker dissolution. Too much agitation can also wash fines into the tip of the filter and clog it, extending brew time. Since the amount of turbulence you introduce is difficult to make repeatable, most people pour from low-ish so they're not mixing things up too much.

7
-jcsOP•

Okay. The main reason for my question was that I use a hario V60 size 2 when I usually only make one cup. I try to stay as low as I can without coming into contact with the sides of the V60 but there's usually still a fair bit of clearance from the grounds themselves (I use a gooseneck) so I was wondering if there would be any noticeable change in brew quality if I were to get a size 1 so I could get even closer. Do you think this would make any difference whatsoever or would it take a more drastic height change to make it noticeable?

1
MikeTheBlueCow•

I have the 01 and 02 sizes, and I use the 01 size for 10-15g, up to 20g if I'm splitting pours. 02 can handle 20g and up.

1
VoteLobsterV60•

The differences are probably more academic and speculative than they are practical. I'm not convinced you'll taste much of a difference. Using my 01 is easier than my 02 for small batches because it's easier to control where the water goes from a lower height. Never done a side-by-side tasting or refractometer test, though.

1
Zephyp•

Probably not. Which dripper to use depends on how much coffee you are brewing.

1
namegoesherelulzSock Brew•

The agitation/turbulence apparently makes for higher, more even extractions; I pour from as high as I can without coffee splashing out.

1
VibrantCoffeeVibrant Coffee Roasters•

I have found that this is extremely grinder-dependent: if your grinder produces a lot of fines, you are much better off pouring very low and gently. If you have an outstanding grinder that produces very few fines, then the more agitation the better. It also depends a bit on the filter you are using - some seem to be more prone to clogging than others.

3
namegoesherelulzSock Brew•

I use a Comandante, so far from high end but not the worst, and I’ve personally only found improvements with pouring high for the V60 (untabbed and tabbed Japanese filters). With the Kalita however, pouring high always gave me worse results. No doubt it’s grinder dependent, my Porlex would clog at the hint of a breeze, let alone high pouring.

1
Zephyp•

I don't want to discuss semantics, but I would say a Comandante is a higher end grinder in the consumer market. It's one of the best hand grinders out there and you need to dish out a lot to find a comparable electric.

1
coffeeadastra•

At least with high quality (low fines) grinders, I totally back that comment. I find turbulence easily repeatable, as long as you have enough of it. Make sure you dont move horizontally too fast because that will cause an uneven coffee bed. Also make sure to swirl immediately after each pour, I think it’s even more important with high pours.

1
namegoesherelulzSock Brew•

Does swirling immediately after pour vs swirling when it’s like 2/3rd-ish down (I think I got that from the Rao video?) make a difference?

1
coffeeadastra•

I think it would. Swirling equalizes the coffee bed which is great for uniformity, but swirling after drawdown started could break channels that started forming. It’s like preventing vs fixing; I think the earlier is better, but I actually didn’t try both to see the difference. I think Scott now swirls before drawdown but I didn’t pay attention to that last time I saw him brew, I completely forgot he swirls after drawdown starts in his Youtube video.

1
qwsfaex•

Not a pro, but increasing the height decreases total brew time, because it makes water drain faster.

-2