Cheat Sheet: Memory Timings for Micron E-die (2x8GB Single Rank 3800MHz) for Ryzen 3000
Hey guys. I figured since the ryzen dram calculator wasn't very reliable for a lot of people (for Micron E-die memory at least) I figured I'd try a more "plug-and-play" kinda approach. This sheet is a result of it.
A couple of things first: To figure out the maximum clock speed of your CPUs infinity fabric (3600 is guaranteed by AMD, but there are 2 "steps" you can possible go higher before it switches to 2:1, being 3733 and 3800).
I recommend leaving any and all settings in your mainboards bios at stock default (you can always change things after getting your memory stable of course). Literally only change the infinity fabric clock speed (FCLK) to 1900 aswell as the DRAM Frequency to 3800 (like I said, leave all the timings and voltages on stock, for now).
If you do not manage to boot with these 2 settings, you will want to reduce your fclk and your dram frequency to 1833 and 3733 respectively (if this also fails to boot, you will have to settle for 1800 and 3600. This is all purely silicon lottery)
Now, just managing to boot into windows dosen't mean much yet. You will want to check your memory latency first. To do so, you can either use the built in latency test of the ryzen dram calculator (in the membench tab), or use Aida64 for the latency benchmark. You will know if your infinity fabric still runs at a 1:1 ratio if your latency is in the ~70ns range. 2:1 usually ends up in the ~90ns. (move one step down if you do not get the 1:1 ratio, so from 3800 to 3733)
Ok. So now that you got your memory clock speed set, we can move on to actually talk about the cheat sheet. First up are the "Primary Timings". You will see that the sheet has columns for all kinds of different timings. The first column; "Rec", obviously short for "Recommended" are simple the settings I'm using right now. They can be your "guide" on what to possible expect.
Anyway, you will want to start by applying the primary "safe" timings first. Once you're in windows again, launch up the built in membench of the ryzen dram calculator, set the benchmode to "memtest", the ram size to 14000 and the task scope to 1200. Then hit the little "clear standby" button on the bottom, followed by "run".
(Note: you could possible hit the max ram button after clearing standby, but since windowes resource manager is rather bad, I recommend leaving a static ram size of 14000 instead or else you might run into issues further down the line)
After finishing the first stress test step (hopefully successful) you can move to the "Secondary Timing" section. At this point I'd like to actually shed some more light into the effect of some specific timings:
The 3 timings which are by far the worst on Micron E-die are:
- tRCDRD
- tRC
- tRFC
These will usually be much lower on any other memory die. So don't expect them to be comparable to others.
Another thing is, while other memory dies like a higher than default voltage, micron e-die does not. In fact, I found it to be very unstable, as in, you get more memory errors the hotter they get. So to have them scale beyond 1.40v, you will either have to put a fan on them, have some other kind of reliable cooling, or settle for 1.40v.
But don't worry about voltages yet. All the "Rec" timings I achieved were with the stock 1.35v and I really don't expect it to be much different for everyone else.
So as I was saying, "Secondary Timings":
They can help you get some more performance on top of your primary timings. Especially tFAW can speed up the memtest quite a lot. It is tied to tRRDS, so you will want to always have it at a minimum of 4 times that value: e.g. tRRDS=6, tFAW=24
Wow. That is quite a lot of text I ended up writing and if you read it all up until here, I must tell you it is not over yet.
I'm not gonna go into any detail about the "Tertiary Timings", as I would expect most people who make it trough the hours of testing for primary and secondary timings do not have much patience left to tweak them aswell. And since they are pretty tight already even with their "safe" values, you wouldn't get all too much performance out of them anyway.
Instead, I'm going to talk about "Additional Settings" The only really interesting part in this section is the fact, that you can get "true" 1T for the command rate "Cmd2T" by simply using all the "Extreme" values of this part of the sheet. I don't have much sample size on this, but simply having the ClkDrv at 120 ohm instead of the default 24 ohm allows us to disable GDM (Gear Down Mode) and PDM (Power Down Mode) and set CMD2T to 1T.
(Again, if this should not work for you, no worries, just leave it all on auto, but 2 people where be able to successfully copy these settings and have it work for them so it is worth noting) And don't worry about the high "120 ohm". It is just for stability sake, like all the settings in the additional section so it won't damage your memory, like a high voltage would for example.
To finish it all up I'm going to go into a little bit more detail on a couple of timings:
-
Trcpage: Should always be left on Auto since it will most likely end up being 0 anyway. Also my bios would always set it back to "Auto" automatically so I expect it to be the same for everyone.
-
Tcke: Leave it on Auto. Will most likely end up at a value of 1
-
Trfc2 & Trfc4: Leave on Auto. They are not used by the memory (I think) 60 is the minimum the bios allows for and it had no effect on stability for me.
-
tRAS: Why did I specify ( tCL + 20 ) you might think? Well, I just found it to be a good average. I could get into much more depth on this setting, but it would bloat this wall of text by another 1000 letters. So just trust me on this.
-
tRC: Is connected to tRAS. Like I mentioned above, it is one of the worst timings for micron e-die, so don't expect to hit the minimum on this.
Last but not least: Voltages: Personally, I just left all the voltages on auto. I don't see much point in adjusting them for micron e-die atleast, as, like already said, they don't scale very well with it. (if you do want to change voltages at all, I recommend the following: VDDCR SoC: 1.025v - CLDO VDDG: 0.950v - CLDO VDDP: 0.900v) these will probably end up below what auto sets them to.
Edit: I've changed the "Rec" column to "Example" since some people (understandable so) didn't read this whole wall of text and plugged them in, instead of the "Safe" ones
Posted Aug 19, 2019, 9:26 PM UTC · edited