Advice on parent's network solution

Advice

Hi all, my parents recently purchased a new house and have asked me to help set up the network. The previous owner wired much of the house with Cat 5e, and my parents want to use it if they can. I figure router->unmanaged switch->access points would be the best use and allow me to set up PiHole, Plex, and other stuff for them as well.

I've researched on here quite a bit and see that Ubiquiti is highly recommended, but I have a few concerns. Would Ubiquiti stuff be wasted on a Cat 5e network, and if so what are "lesser" routers and APs that would be better suited? Additionally, I've read that the interface can be a bit challenging, should I assume that my parents couldn't learn how to use it? And likewise, are there less powerful solutions that have an easier to understand interface? Thanks in advance!

Posted Oct 8, 2019, 8:55 PM UTC

1211
socialyinept4105•

I set up a 3 AP unify setup on preinstalled 5e lines about 2 years ago for my parents and it works great. The cloud key is a smart idea so issues can be resolved remotely.

Pick up a cheapo continuity tester and test each line/wall jack thoroughly. Badly punched wall jacks were the bane of that install.

6
brettinternet•

Did you install the unifi security gateway or some other firewall, too? I'm wondering about what to recommend to my non-technical friends for a firewall of similar quality to unifi.

1
socialyinept4105•

I didn't worry about the USG as the plan was to go with an edge router but that got quashed as overkill since the isp supplied their own. Who am i to argue.

1
42DimensionalGoFishOP•

Thanks for the advice! The cloud key makes sense now that I think about it.

Most of the lines are unterminated, so I'm already planning on borrowing a friend's crimper and continuity tester.

1
KingdaToro•

Crimping RJ45 plugs onto installed cables isn't good practice. It means you need to manipulate them whenever connecting or disconnecting them, which risks damage. It's much better to terminate them with punch-down keystone jacks. This way, they never have to move once they're installed and terminated. Then you just connect the jack to a device or switch with a patch cable, which is trivial to replace if damaged.

The only exception to this rule is for installed, PoE-powered devices such as APs and security cameras. In this case, crimp a plug onto the installed cable and connect it directly to the device.

2
42DimensionalGoFishOP•

Ideally I'd like to do that, but the wiring is weird; most of the ethernet comes out of various holes in the wall with a bunch of other cables (basically there's a couple entertainment centers with HDMI/speaker wires coming out of a hole in a cabinet, and the ethernet comes out the same hole in each cabinet). I know it's a nightmare and I'm already planning time to fix it over Christmas, but for now I just want to get my parents set up.

1
KingdaToro•

Actually, keystone inserts are specifically made with that sort of situation in mind. You can get keystone HDMI couplers, Coax couplers, and speaker wire couplers. As long as you don't have more than six cables coming out of a single-gang opening (with a speaker wire pair counting as two), you'll be able to manage them with keystones.

3
zfa•

You can also install the unifi controller in the free Google Cloud Compute tier, if you have a Gmail account.

1
xyzzzzy•

Unifi is fine. FYI cat 5e supports 10Gb speed up to 45 meters. Cat 5e is fine.

3
jlaux42•

Unifi runs on PoE, so you might want to buy a PoE switch. (This could also be good for security cameras.)

You might want to pop open some of the Ethernet jacks in the house and make sure all 8 wires go to the jack, and that they didn't split some wires off for phones or other things.

2
[deleted]•

[deleted]

0