[Review; Squonkvember, day 5] FLVR (SXK)

Review

Welcome to this week's last entry! Today's review is going to be a rather short one; sometimes not many words are needed...and sometimes a single picture is all it takes.

FLVR (SXK)

The National - Bloodbuzz Ohio

choo choo next stop FLVR town choo choo

Table of contents

  • Hard facts
  • Soft facts
  • Totally personal take
  • Pros/Cons
  • Squonkvember
  • Disclaimer

Hard facts

  • Measurements (without drip tip and 510) 22*16 (!) mm
  • Build deck is a standard two-post build deck
  • Airflow the draw very restricted but still RLH
  • Something noteworthy about the goodie bag? nope
  • Anything else? nope

Soft facts

The way the FLVR looks is totally my jam. Not only do I like sand-blasted caps, I also think they go nicely with pretty much every color. which means the FLVR looks great on every mod I put it on.

Overall, it looks like someone shrunk Le Supersonic, which is far from the worst thing one can do.

Building is almost as easy as it gets; two-post deck, with grub screws for the lead. No notches for the coiling rod, but they are also not necessary. I just wished there were some ledges to hold the leads in place while screwing them down.

Airflowwise, the design is just as straight forward. Three holes per side, and the channels are angled down (so no fear for oversquonking).

as straight forward as it gets

Fully open, it's a very restrictive hit, pretty much on the lower end of what I consider RLH. When closing down the holes, the draw gets a bit more restrictive, but not by a lot; I guess there is still some air going in, which isn't surprising considering that the airflow is still part of the post, so in order to close it off completely, it would need to touch the top cap which would result in a short.

Yet again, I really don't want to take a neutral stance, way too emotional for that. So let's head to my

Totally personal take

Sometimes I wonder if it would be feasible to do reviews only by showing pictures. Surprisingly, this is a fuckton of work for most devices. With the FLVR, however, a single pic suffices

so fucking nice

Seriously, look at that combo. Do I really need to go over performance?

So, only for the sake of completeness:

No matter the amount of open holes, the draw is really fucking smooth. Such a joy to toot on. And flavor, you asked? In-fucking-sane. It's on the same level as the Venna and Le Supersonic, so tied for third best of all the RDAs I tried (Basic still rocking first place with the FeV BF-1 RDA coming in at second place).

So, fucking smooth, and fucking great flavor, can it get even better?

Yes :)

Because of the way the airflow is set-up, I'm able to get bigger coils in compared to the Venna, which means that a) it's easier to put on a mech, and b) I get bigger clouds, which is the only thing I always wished was different with the Venna.

Conclusion: the FLVR is fucking insane. If you want an RDA that bangs as fuck, go for the FLVR.

the ticket to FLVR town

I fucking love that RDA :)

Some music that goes well with it: Funky ABBA by the Nils Lundgren Funk Unit. Just like the FLVR, I can't play it all the time, but I love that's in my collection and sneaking one or two songs into a playlist is always worthwhile. However, that shit is kinda niche and the FLVR probably is good for a bigger audience, so let's go with The National and one of my favorites: Bloodbuzz Ohio.

Just like the FLVR, it's a pretty restricted affair and most of the time I look for more BAM, but I certainly can't deny how sick that sound is :)

Pros/Cons

ProsCons
flavor
clouds
smooth
flavor
clouds
smooth
flavor
clouds
smooth
flavor
clouds
smooth
flavor
clouds
smooth

Squonkvember

My expectations for this one were really high, because of the way the airflow is set-up. I saw no possibility for it not to bang. And oh my dear lord, does it bang. I really never thought that I would find an RDA that would replace the Venna for me, but here we are. What a sick RDA to end the first week with :)

Which says a lot, because 4 out of the 5 RDAs I reviewed this week have been winners in my book. I was expecting 2 (FLVR and NarEA), so ending up with twice as many sick bangers certainly was a nice surprise.

I also like the spread of airflow options; the FLVR and the FeV BF-1 RDA (that fucking name) clocking in at the lower end of my comfort zone, and the Skyfall and the Hadaly pushing the opposite boundaries. Yeah, color me satisfied.

Hopefully, next week will be just as great and maybe we can fill in the void between fairly RLH and almost open DTL.

​

RDAAiriness: sucking on a straw to barn doorSmoothness: fasten your seat belts to butterMy thoughts summarized with an ASCIIStar reviewFinal thoughts
FLVR (SXK)■□□□□□■■■■■♥ヽ(´ー`)ノ♥★★★★★that flavor, them clouds, that joy :) one of the very best RDAs, no questions asked

Info & Disclaimer

  • The FLVR (SXK) was bought with my own money.
  • All of my reviews along with my recommendations can be found in this reddit post. If you enjoy filtering and sorting, I also packed my summary tables into a goggle spreadsheet.
  • I'm a lazy fuck. And English isn't my first language, so please bear with me.
  • A proper disclaimer can be found here.

Posted Nov 15, 2019, 4:30 PM UTC · edited

2342
Badazdwww.badazdcoils.com•

Can confirm, the FLVR does indeed bang so hard that you just can’t put it down. It’s practically my favorite ATM. Looks sexy as hell on everything, the flavor pops with all the builds I put in there.

I was skeptical at first with how close the positive post was with the wall so I used it on semi regulated mods and regulated mods at first but I never had a short issue pop up.

So good another one is in my cart and will be ordered real soon.

3
IPDNOP⏍⊂(•ヮ•)ҩҩѠѠѠѠ•

was waiting for this very comment lol

2
HotSauceVillain•

Holy crap another banger? This has been a great string of reviews so far! Just when I think I've decided on what to get another one comes along lol

2
IPDNOP⏍⊂(•ヮ•)ҩҩѠѠѠѠ•

The FLVR's not the last one lol

2
HotSauceVillain•

That's wild. I might have to get 2 or 3 for Black Friday then 😂

I was about to order the FEV BF-1 from 2fdeal but maybe now I should wait in case one of the next ones you review tops it lol. Or in case there are others that I can only get from 2f, like the Ulton BF-1.

1
IPDNOP⏍⊂(•ヮ•)ҩҩѠѠѠѠ•

Or in case there are others that I can only get from 2f, like the Ulton BF-1.

there actually is one ;)

2
HotSauceVillain•

haha I think I know which one that is so I shouldn't have to wait very long for your review on it then :)

1
Cid-Conray•

thanks again for the review.

so now i have another RDA on my "have to try" list :p

2
86birdie•

I’m so glad to have read this. I ordered a sxk FLVR rda a few weeks ago and it should be here Monday. I’m super excited to get it now.

2
IPDNOP⏍⊂(•ヮ•)ҩҩѠѠѠѠ•

enjoy :)

2
86birdie•

I must say, this little thing is great. Tossed in a build at .53ohms at 31 watts, and I know have found the perfect atty for my Aegis Squonk. Great flavor, smooth restricted draw.

1
Anaali37•

Hey thanks a lot for your reviewa and hardwork! I'm thinking of a single coil flavor banger. I'm currently on the Mjolnir Rda. I squonk too. So between this and the basic which would take a 4mm coil better?(sfq 28 badazd I've noticed you're using his coil) ...I really don't wanna unwrap and wrap again. Also is SXK the way to go with both Rda's?

2
IPDNOP⏍⊂(•ヮ•)ҩҩѠѠѠѠ•

yes, I'm using SFQs, but in the FLVR I have a SFQ30
no need for the bigger gauge
first of all, good luck finding a basic; it's been discontinued for quite some time now, maybe you can find one by Kindbright (last time I checked, there were some left at some store I can't remember right now)
as such, FLVR pretty much is the way to go; if the SXK is better than other versions, I can't say but I'm totally satisfied with the quality

having said that, I serioulsy doubt you can comfortably vape a 4mm coil inside the FLVR; if you rock that coil in the Mjölnir right now, I suspect it's quite a lot of mass, something that the FLVR neither wants nor supports
if you don't want to get some other SFQs, either try some single core claptons, fine fused claptons (30ga, dual core 28ga should also be okay) or just round wire

2
Anaali37•

Thanks for the detailed advice..I actually found the sfq28 4mm to taste much better in the Mjolnir than the sfq30 4mm..if you happen to try a 4mm in the flvr let us know

1
IPDNOP⏍⊂(•ヮ•)ҩҩѠѠѠѠ•

yeah, the Mjölnir needs quite some metal; for reference: I'm using a framed staple in it...

when I find the time I throw a bigger coil in and let you know

1
corncribbage•

Great review and song choice. It came thru on my playlist just last week and was stuck in my head for several days.

2
IPDNOP⏍⊂(•ヮ•)ҩҩѠѠѠѠ•

since witing the review it's also stuck in mine :D

2
aberz0202•

Much Love, just got 2 :)

2
IPDNOP⏍⊂(•ヮ•)ҩҩѠѠѠѠ•

awesome :D

2
joeblowmaArcticFox Junkie•

Well I never...

side and top

This is another one that can fit a wasp nano cap almost like it was made for it; doesn't get you more air but you can build a bit bigger/higher (actually you have to, or flavor suffers due to the now larger chamber) and not wind up with singed lips, or even add a normal height 510 drip tip (if your wasp cap fits it).

2
IPDNOP⏍⊂(•ヮ•)ҩҩѠѠѠѠ•

You posted this pic somewhere else as well, right? Got me totally excited because not too long ago I got some resin wasp caps. In my next rotation I'll use a purple flvr on my purple Luna :)

2
joeblowmaArcticFox Junkie•

LOL I shouldn't be surprised you saw that, but yeah in the discussion section of the silver one on FT someone asked about it and it kinda floored me - I never even thought to check, I just made a less beefy coil when the whole thing was getting too hot. Figured I should dig this up and post it here too before reddit archives it, took me a few days though xD

BTW, I had put smaller o-rings on mine because the cap was shredding the ones it came with but the wasp cap fits a little too loose with the smaller o-rings. Not sure how the resin ones stack up size wise to the plastic ones though.

2
IPDNOP⏍⊂(•ヮ•)ҩҩѠѠѠѠ•

LOL I shouldn't be surprised you saw that, but yeah in the discussion section of the silver one on FT someone asked about it and it kinda floored me - I never even thought to check, I just made a less beefy coil when the whole thing was getting too hot. Figured I should dig this up and post it here too before reddit archives it, took me a few days though xD

saw that post on FT as well and was also baffled lol
than I forgot about it without trying, so thanks for sharing :D

BTW, I had put smaller o-rings on mine because the cap was shredding the ones it came with but the wasp cap fits a little too loose with the smaller o-rings. Not sure how the resin ones stack up size wise to the plastic ones though.

funnily enough, on mine the translucent cap spins freely :)

2
nerdabilly•

tangential question.... for an RDA like the FLVR, how does the SXK (clone) version compare to the authentic? Some of these RDAs go for $100-$150 authentic, I've been in the market for a 22mm squonk atty but I don't like to buy clones and I really don't like single coil attys. Been thinking of trying a few clones though to get an idea of what RDA might work for me.

1
IPDNOP⏍⊂(•ヮ•)ҩҩѠѠѠѠ•

from what I can tell, clones nowadays really are 1:1. Same deck, same airflow situation, same dimensions, same performance. Build quality ranges from very decent to insanely well made (Ulton is the shit). So far, I've ran into only two problems (the squonk pin on the Squi had no cut-outs for the allen key, it was just round. The O-rings on the MavT were very shitty; top cap would pop off and the AFC was almost unusable).

If you can, pick up a clone by Ulton. If you don't like single coil attys, there are also 22mm dual coil ones (M-atty, Armor v1 and v2 for example).
If you don't like single coil RDAs, because of the restriction, have a look at the Wasp Nano. It is truly bonkers. If 24mm is also okay, consider the .blank. It is fucking open.
If you well me, what you are looking for, I can recommend you something; of course, also a handfull of RDAs so you get a range of different attys right from the start.

3
nerdabilly•

So a couple months ago I was lucky enough to score a Peon squonk. This mod had been one of my unicorns for a while and I was thrilled. Come to find out though, it is so tiny that realistically you can only put 22mm RDAs on it. 24s work, but they have ugly overhang and I'm big on aesthetics. And unfortunately, the vast majority of 22mm squonkers are singles. Anyway, I tried a few different things. I have tried plenty of single coil RDAs and given up on all of them. (Wasp Nano RDA & RDTA, Blitz Ghoul, Mjolnir, GR1, DotRDA Single, a couple others). Same issue with all of them, they just don't put out a big enough cloud to deliver enough nic. I am constantly puffing on them and never quite feeling satisfied. Puff, puff, puff. Still not there. I even dropped like $60 on a Wick't RDTA hoping a higher quality atty might be different. Nope. The Wasp is ok with a fat enough build but still lacks some of the cloud density I like. I got rid of my old Wasp RDA, still have the RDTA, I've considered getting another one though and giving it another shot. Heard a lot of good things about the Tobhino but I'm hesitant to spend more on another RDA I'll probably just give up on.

I did end up finding a few that worked fairly well. The Pindad RDTA was the clear winner here. Great flavor, dual coil, and a little added capacity. plus less squeezing the squonk bottle. I also got an Axial RDA which I can't offer much of an opinion on because my GF has been hogging it :). I also found a Royal DB clone on FT which worked fairly well, quality left a little to be desired and it got a tad too hot but for $8 it worked well enough. I try to buy authentic when I can but fuck anyone who wants $220 for one atty lol. And then I got the squonk adapter for the old 22mm Petri RDA, works decently well but I'm not totally happy with either of the caps for it.

Anyway thanks, I might try the M Atty or an Armor.

1
IPDNOP⏍⊂(•ヮ•)ҩҩѠѠѠѠ•

ok, that's a very specific problem lol
If the Wasp isn't enough for you, you are pretty much out of luck; it's the 22mm RDA that supports the biggest builds
also not sure, you can cram a big enough dual build into the dual coil 22mm RDAs (haven't tried any of them, but they seem to support smaller builds than what one would usually rock in 24 or 25mm RDAs)

having said that, wait for the B2K review; I haven't done all the testing yet, but you can throw some big ass shit in there and also use a dual coil set-up; it's 23mm, though, not sure the Peon supports it

other than that: maybe try upping the nicotine for single coil usage?

the Peon is such a nice mod, would be a shame if it ends up sitting there unused...

2
nerdabilly•

lol it is, and between the Pindad and the Petri I've gotten plenty of use from it so far.

Oddly enough, my usual dual coil mech build is just simple 24 Ni80, 6 wraps, 2mm. I thought I could compensate in a single by doing a parallel build or just using something fat like a fused Clapton but it was never quite the same.

2
joeblowmaArcticFox Junkie•

This one took my favorite spot away from dpro mini, only thing that's bothered me with it is the half height on the drip tip bore... had to cut down a slightly taller tip than what it came with to be completely happy with it.

1
IPDNOP⏍⊂(•ヮ•)ҩҩѠѠѠѠ•

oh, the dpro mini is a very nice RDA, and I totally understand why it got benched by the FLVR
kinda similar, but I think the FLVR is more effortless

2

I have been curious about this one. It just looked too similar to others I have though. I wanna say I saw it after I got the KRMA and thought they'd be similar enough.

1
IPDNOP⏍⊂(•ヮ•)ҩҩѠѠѠѠ•

very very different
the FLVR tramples all over the KRMA IMHO, the way that the air is set up is so much better than what's going on with the KRMA
but then again, I really dislike the KRMA and know that a lot of people actually like it a lot shrug

2

It may have been a different one, I don't recall. I've been getting too many single coil rdas lately.

I like the KRMA, but find myself using others over it constantly. Although it has had a permenant spot on my 21700 squonk since I got it, I just rarely use that mod.

1
IPDNOP⏍⊂(•ヮ•)ҩҩѠѠѠѠ•

It may have been a different one, I don't recall. I've been getting too many single coil rdas lately.

I know that feeling lol

I like the KRMA, but find myself using others over it constantly. Although it has had a permenant spot on my 21700 squonk since I got it, I just rarely use that mod.

yeah, this I know as well
some attys just don't enter my rotation often enough

1
hammerzam•

This may sort of off topic but what build would u recommend for this on a single 18650 unregulated?

1
IPDNOP⏍⊂(•ヮ•)ҩҩѠѠѠѠ•

SFQ30 by u/Badazd
3mm ID and 5/6 wraps
performs heavenly from 4.2v down to 3.3v

2
supercubansandwich•

u/nerdabilly Yeah, I just picked up and m-atty clone. I run the same coils in a dual configuration. I normally use single coil rdas, and this m-atty is giving me a head buzz for the first time in a long time. It might be a good choice for you. There is also the Armour V3 22mm dual coil rda, allthough I’ve never used it.

1
nerdabilly•

awesome, I'll have to check that out. for m-atty clone is really the only option, they only made a super limited run of the authentic (less than 1000 I think) and even on the secondhand market they sell for hundreds or even thousands.

Where did you find the m-atty clone? FT appears to be sold out/discontinued

1
supercubansandwich•

Have you tried Alibaba.com? I’m currently working in China so it’s easier to find these Chinese clones. I could probably help you get one, but you’d (probably) end up paying $50 for the clone + 4-6 day shipping.

1
nerdabilly•

I haven't, usually FT and sometimes 3f is where I check. I'll look there

1