Dovpo Clutch SQ vs Topside SQ: big voltage drop in the topside not the Clutch

I bought a Dovpo Clutch SQ then a week later got a Topside SQ.

The topside has tremendous drop volt with the same same rda (Tauren solo 0.16ohm) and the same 21700 (30T). It has a very slow ramp up compared to the clutch. When I just received it it was a great vape but, later in the day, the ramp up increased. Even with a fresh 30t. Battery last half as much as the Clutch.

I dismantled the topside, cleaned the silver contact with scotch brite there were some black marks (I think it's arcing marks). I didn't touched the gold plating near the floating 510 pin. The plating might be degraded.

I took 3 puff with each of them: with the Topside 3.87v to 3.82v and with the clutch 3.82v to 3.81v !

I bought both of them new.

Does somebody well versed in mech know what could be the cause ?

Posted Feb 19, 2020, 5:33 PM UTC

63
Dovpoecig•

Hi u/beam84 can I see a photo of the brass plate on the 510 of your SQ Topside? If there are any problems with your SQ Topside we can help you by emailing us at [email protected]

There is really a huge difference on the performance of the Clutch compared to the SQ Topside. Because the Clutch is a Hybrid mechanical mod that is directed to the battery.
If you still have any concerns please message me and I will help you out. Thank you!

1
beam84OP•

In this youtube (https://www.youtube.com/watch?v=cKo7AJwrsXU) review comments Drip N Rip wrote:

​

All fit and work well. Initially my SQ performed flawlessly. Over time, pressing the switch became more hit and miss... Now, I can’t hardly get it to fire at all. As this difficulty was developing I noticed that it seemed as though I had to depress the button more firmly to get it to fire. I’ve taken the door off and visually inspected what happens when I depress the switch..(lock is vertically set=off) ..90% of the time nothing happens...10% of the time I will see a tiny spark at the contact.

This is what happens in mine.

2

i just bought one of these new from EV cig and it is very disappointing... it hits very weak... using charged Molicel battery, Bonza at .15 and then a Goon at .10 .... far from hard hitting.. my Vindicator clone hits 10x harder... it was $15 ..... this SQ was $150... wtf..

1
beam84OP•

I resolved every problem I had by using scotch brite on the contacts (top plate and silver part).

Check your 510 screws to be tight enough.

You can watch the mooch youtube video about the clutch.

1
beam84OP•

Thanks for your reply :)

Here are some pictures: https://imgur.com/a/E94ELUR

The Topside plate seems to be gold plated not brass. Are you sure it's brass ? Can I use scotch brite without removing the plating ? The clutch one is brass.

There are some black dots on the silver part which I previously removed. They came back when I compared for a second time the two mods back to back.

I know there are differences in performance but right now the ramp up is 7 seconds longer in the topside. Which is a massive drop volt.

The rda I used on both mod is the tauren solo with a 0.16 ohm coil in ss inowire (https://www.ino-factory.fr/en/inowire/3-inowire.html). It's a hollow wire which is really responsive.

I didn't compare the performances with the RDTA it's just there because that's what I will use the topside with when it will hit reasonably.

For your information I bought the clutch on the Signature Tip website and the Topside SQ with the wholesaler https://www.gfc-provap.com. No european wholesaler sell the clutch.

I own a vapeshop in France.

1