Over extruding? How can I get rid off this corner bumps... ABS

Over extruding? How can I get rid off this corner bumps... ABS

Posted Jun 19, 2020, 4:29 AM UTC

811
chasm3D•

Can you post your gcode. I can take a look at at what the printer is being commanded to do in the corners. At least we can try to find if its the printer or the slice and its settings.

4
industrialcoderOP•

Thanks!

I pasted the whole gcode in this pastebin since I wasn't sure what sections were the important ones

1
chasm3D•

So when one of the squares is finished, the filament is retracted. The nozzle is then slid along the previously printed line for 10mm which is a wipe move. The nozzle is moved to the start of the next square and the filament is fed back to the point it was at when the retraction began. You can see where the wipe move ends in your picture. Its where you see the thin strand between the one square to the corner of the next square. After the retraction is reversed, the nozzle prints out the square. Then the nozzle is moved 0.1 mm over and it reverses direction and prints the same square again. As the second line is only 0.1 mm from the first you are getting alot of overlap as I am assuming you have a 0.4mm nozzle. It then repeats the retraction and moves on to the next square etc.

What are your settings in Cura for the line widths, the wall thickness and wall line count. It looks like your retraction is not working properly. But is it not working because your settings are off or is it because it's scraping against a higher than expected wall due to printing one line almost on top of another? As well with the wipe any oozing filament should have been removed from the nozzle. In fact I would say with the wipe and the short distances involved, you probably did not even need to retract at all.

Hopefully there is some miss setting of the parameters I asked you to look at.

2
IvorTheEngine•

Maybe increase the 'jerk' setting, so the nozzle doesn't pause for corners?

3
industrialcoderOP•

I'm not sure whats going on, I'm trying to level the bed and seems to be working except I get these bumps on corners where new material is added.

​

Ender 3 Pro, Magnetic bed

CURA:

Material: Amazon Basics ABS

Layer Height: .2

Printing Temperature: 245 (then prints separate if using lower temps)

Bed Temp:80

Retraction enabled

Retraction distance: 6.5

Retraction Speed: 25

2
scufflingPrusa i3 Custom•

It's stopping on those positions to retract then step to the next position. Try doubling your retraction speed (or as high as you can go without grinding filament).

2
DictatorDoom•

All I could think of is printing temp but 245 shouldn’t be a problem for abs. You sure it’s abs? Maybe you mistakenly used pla?

2
industrialcoderOP•

100% Positive its ABS, actually I mistakenly ordered it and went through hell trying to print with it thinking it was PLA.

This was like two months ago before upgrading to an SKR mini 3E V2

1
DictatorDoom•

Do you print the abs in a box? Or just in an open room? If you don’t know what I mean I can send a pic

1
GB_Morning•

Look for coasting. It should help.

2
AutoModeratorMOD•

Hello u/industrialcoder,

As a reminder, most common print quality issues can be found in the Simplify3D picture guide.

Please remember to include the following details to help troubleshoot your problem.

  • Printer
  • Filament Material and Brand
  • Nozzle and Bed Temperature
  • Print Speed
  • Nozzle Retraction Settings

^Additional ^settings ^or ^relevant ^information ^is ^always ^encouraged.

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

1