r/livesound•
kelcema

No Stupid Questions Thread - Week of 2020-08-17 - 2020-08-23

The only stupid question is the one left unasked!

Do you have a basic question you want answered? Let us help! Remember that r/livesound is for PA/sound systems/streaming -- we may not be able to be as helpful with questions about, say, home theatre systems. Keep in mind that the more information about your setup (amps, speakers, mixer, microphones) you can provide, the quicker we'll be able to help you!

Posted Aug 17, 2020, 5:03 PM UTC

917
Dart_HS•

So I have a large speaker (JBL PRX615) that I have always used an XLR --> Aux cord hooked up to my phone for music.

Now I am looking to place my speaker on my balcony (4th floor) and play music while at the pool wirelessly. Would anyone have good recommendations to do so? I am looking at XLR-->bluetooth receiver options and even XLR-->aux cord then aux-->bluetooth receiver.

Here are the two options I have found thus far but would love recommendations, preferably within a reasonable price range:

  1. https://www.amazon.com/Alto-Box-Bluetooth-Total/dp/B01NBWON6F

  2. https://www.amazon.com/dp/B07KTK8YP3?tag=jaehong-20&linkCode=ogi&th=1&psc=1#customerReviews

Thank You!!!

2
kelcemaOP•

The products you linked claim a range up to 50' (for the first one) and 197' (for the second one). Without any experience with any of those products, it's difficult to say one would be better than the other.

Side note: the reason you're probably not going to find a lot of experience with Bluetooth devices for audio transfer on here is that Bluetooth is something we really don't rely on in a professional setting. It's not something that is reliable enough that I would be willing to risk my reputation on. (Especially if I can just run a cable...) If I need a wireless setup, I would use a standard wireless mic tx/rx kit.

4
mister_damageAudio Dropouts Because Microwave Nachos•

Let's run a BT near a microwave oven and see what happens!

All sorts of fun and intrigue awaits as you microwave your nacho cheese!!

1
Abacadaba714•

Yah I wouldn't do this. I doubt you'll get the performance that you'd expect due to the distance.

1
MarqDewidt•

I have an Allen and Heath Qu 24. I'm under the impression that it has mic presets for whatever brand/model of mic you're using.

If that's the case, what's the step by step for setting channel 1 to a Shure 58 beta? I can't seem to find anything online.

2
kelcemaOP•

Select the channel, tap PEQ on screen, Press FN button to goto library.

(Answer sourced from A&H's website. I do not have a Qu24 to verify this as being correct.)

That being said, if you read that thread, there's commentary about how 'good' those presets are. As with everything in audio, ask yourself, "how does this sound?" A preset is a starting point, and just that. Don't get sucked in to the illusion that it'll be a one-shop-stop-for-all-of-your-tonal-needs, as it'll vary based on the sound system being used, the performer, their microphone technique, the stage arrangement, the room/venue/space, and even the weather.

3
Dngvasht•

Sweet mixer. I have the qu32. Never used the mic presets but I might give it a shot for fun.

1
D-townP-town•

Download the QU Mixer Reference Guide.

Go to Section 9.5 Processing Libraries. Read and understand the concepts and options presented.

A list of both general Allen & Heath and mic-specific ProFactory libraries is in Section 9.6 List of Factory Libraries.

Press the channel 1 Sel button, then on the touchscreen choose the PEQ tab. Beneath the touchscreen press the Fn button. Apply the instructions in Section 9.5 to choose from among the included ProFactory libraries. The Shure Beta58 is *B58VOX.

2
[deleted]•

Hello, tried to make a thread for this post but appears my account is too new so need to post it here.

I've been predominantly on the studio and recording side of the audio world for a fair few years now, and thought I basically knew everything there was to know about audio and equipment. While looking at a small second hand PA system that has come up for sale locally, I've quickly found out I know nothing at all really about live sound setups at even a small scale, and wanted to ask a few questions and get pointed in the right direction if at all possible.

Basically I'm looking at getting a used pair of Funktion One Resolution 2 MK1s. These will be used mostly for mix purposes in a studio, the odd party, and to be dragged to a party maybe 2 or 3 times a year (COVID permitting). I'm aware F1s aren't the best value or sounding PA, but I work with and play predominantly House/Techno, and these are the industry standard for the scene. I'm thinking it could be beneficial to have these to refer to when mixing, and a lot of fun.

So what do I need to actually get them on, and playing music? I've tried to do as much research as possible, but information is sparse on the the F1 website, and I'm having a very hard time understanding and parsing a lot of terms used in PA. This is basically what I've determined is needed in the chain, but i'm not confident in it at all:

Source (DJ mixer, 2 channel) > PA manager/processor (outputs 4 channels, L Low+High, R Low+High)> Amplifier (4 in, 4 out)> Speakers.

Is this correct? To my understanding the PA processor takes the source program, and first of all applies a limiter as protection. From there it applies a delay to the different speaker drivers as needed(found information on the Res2 setup here: https://www.funktion-one.com/crossover-settings/resolution-2/ ), sets the crossover point, and applies gain where needed? (8dB to bass driver in this case). From there it supplies an output for each driver, which gets amplified and sent to the speaker.

In terms of a recommended processor/manager, is this something that say DBX DriveRack PA2 would be able to handle? Would a more budget option such as the Behringer Ultradrive DCX2496LE do just as good as a job?

Now in terms of amplifiers, I'm pretty confused. I take it I'll need 4 channels of amplification. Can I use 2 standard 2 channel amplifiers such as the Behringer A800 here? Or is a dedicated 4 way unit the preferred setup, such as say a QSC PLD42, which also has built in DSP? Is volume set and forget, and how is it handled when split across 2 different amplifiers?

I hope that all makes sense and isn't just the ramblings of a mad man. Any advice is much appreciated.

1
D-townP-town•

You're definitely on the right track. Your signal flow goes from the DJ mixer, out to the system processor, then to the amps and speakers. You will need 4 amp channels, and how you derive them is entirely up to you. You could go with two identical 2-channel amps, or two completely different 2-channel amps, or a 4-channel amp. You can get amps with some level of DSP built in, or basic amps without processing. None of these are necessarily "preferred" over the other, they each have their advantages and disadvantages. If it were me, I'd be looking for a couple of matched, 2-channel, non-DSP amps.

As far as the system processor, again lots of options. In the lower price range, the dbx PA2 isn't a bad choice (although u/ihatetypinginboxes isn't fond of them). The Behringer DCX2496 is another capable contender that has stood the test of time. Some people favor the Ashley Protea line, though I'm not sure they have any low-cost units in their current product line, you can probably find a 3.6sp used for a reasonable price. A used dbx 260 would be a candidate too.

Your understanding of the processor is in the ballpark, although the order of the processing modules would usually have delay and limiting at the end. If you think about it, the first thing we need to do is to divide the full range signal into separate passbands appropriate to our speaker drivers, (aka setting crossover points). Then would come the delays and limiters, so that they are only affecting their particular passbands. Make sense?

Setting up the amps is where it seems you have the most questions. There are several variables here so it's hard to make more than generalized statements. The DSP can compensate for different gain requirements of different amps. Your amp gain controls would usually not change once you have them set, though this isn't set in stone. The overall system volume in your setup would be the DJ mixer master output control.

This sounds a lot more complicated than it really is. Based on what you've posted, you're probably 80% towards understanding this well enough to get those F1's singing. Let us know when you have your amps and DSP, and we can go from there.

1
tikacademy•

Simple question probably, but I haven´t been able to figure this one out..

With a XR18 can I route a BUS to USB and send something like a monitor mix into OBS for live-streaming?.

Thanks

1
AdamnBarber•

Hello, my band uses a Behringer xr18. If anyone could explain to me how to make it so I can hear my whole band through my in ears that would be awesome! I can only here the vocals currently. Is there something I need to plug all the transmitters too then plug into the head to get the whole band, and then make my mix? Any help would be apreciated

also reading some stuff online I was thinking an aviom 320 would combine all our mixes so it could be personaly mixed individually by all of us digitaly?

1
tikacademy•

Tired of seeing the way old RTFM instead of a real answer, you don't come to these forums to see that, trust me it's frustrating and I´m more than sure that people struggling with an issue whichever it is basic, advanced what have you and seeing some a_______ telling you to go read a manual which he probably has already read or he already fixed the issue you have and can help why taking the time to mess with readers and discourage people?.

After this reflection, and the title of this thread I invite you to welcome all questions and if you have the answer to a question, just throw it there.

If you feel inclined to RTFM to someone lay back and let it go, don´t do that, those comments and answer keep people from using these services why take time to elaborate on your problem, write a post and eagerly expect an answer maybe with a solution just to read some fool telling you something that you probably already did RTFM.

I´m sorry if this annoyed anyone, but trust me it´s what millions of people think of these forums when we find replies like those.

If I can help you I´ll definitely give you an answer, if I don´t know I´ll just zip it.

-2†
kelcemaOP•

I struggled over the weekend, deciding whether/how to respond to you. There were two replies to u/MarqDewidt - mine and u/D-townP-town. I don't have a Qu-series board, so I was dependent on an internet search for an answer. u/D-townP-town had more detail than I had. Yes, they said "read the concepts presented in the manual," but they also included a link to said reference guide and more details as to which sections should be reviewed. We both provided the exact steps needed to utilize the microphone pre-sets.

Whereas I agree that a response of just "Did you BOTHER to read the gawddang manual?!?" with no other information is not helpful, we both provided the answer to the question as presented. u/D-townP-town even explained where in the manual to find the solution-- not everyone has a great GoogleFu abilities and I can certainly understand someone not being able to find the exact information they want. Often, that's just due to a lack of using the precise verbiage required to yield results.

This is a "No Stupid Questions" thread for a reason. This is also why I get irked when people downvote initial questions- for that same reason, it's discouraging people from asking questions in the first place! But, that all being said.... I don't think either of our replies were disparaging to u/MarqDewidt in any way. We provided the information needed, and we both linked to our sources for the answers, so they could investigate further if they want.

I think your post accusing us of simply stating "RTFM" was unwarranted and un-called for. I know that wasn't my intention, and I would presume the same for u/D-townP-town. I hope in the future you'll think a bit before accusing others of not being helpful on here.

Thanks for listening,

Ray

5
MarqDewidt•

You guys helped me, thank you. Y'all are right, I didn't read the manual... Cause my approach to finding the material wasn't yielding any results.

A&H's site said to 'download the libraries here', which made me think that the link was simply to the libraries ONLY. Their site itself didn't have any instruction, I couldn't find videos, and couldn't find any forum threads.

Anyways, I got what I needed, which was surprisingly very little... The couple mics I cued up had extremely little adjustments.

3
D-townP-town•

simply stating "RTFM" was unwarranted and un-called for. I know that wasn't my intention, and I would presume the same for u/D-townP-town.

Thanks Ray, as usual you are correct. That was certainly not my intention.

what's the step by step

Someone is asking for the step by step instructions, and the QU manual provides those instructions, along with pictures and tables and other relevant info. In cases like this I prefer to guide the user to that part of the manual, rather than presume that I can somehow do better.

3
AudioThrowAway9999•

Lol

2