Just cleaned up my little HomeLab
Posted Sep 26, 2020, 9:20 AM UTC
8722
Homelab isn't complete without some sort of printer.
2
And the printer has to be physically heavier than the rest of the equipment, or the rack will float away when the fans spin up!
7
Has happened to me several times.
1
REOLHOST4? What's your naming convention?
2
Well, REOL is my Development Nickname, Host because it's a HOST and 4 is an inkrementing Number. The Fujitsu is REOLHOST2, the DL360 was REOLHOST3, The DL380 is REOLHOST4. REOLHOST1 was an old TX100 S2
3
Waitamoment, are you using IKEA Lack as your rack?
2
Yess
1
I plan on building one soon with two of them stacked.
1
Im planing to upgrade to an LackRack Enterprise
1
Devices (from top to bottom)
- Brother MFC-9142CDN
- Devices Behind the printer
- TP-Link TL-WR941ND (flashed to DD-WRT, Access Point)
- Netgear Smart Managed Switch GS308E
- HP Proliant DL380 Gen7
- 2x Intel Xeon E5645 (Currently only one CPU because the fan controller is defective shines. It was displayed that the fans in Bay 4 & 5 are not plugged in. To which I have measured a little bit, I was very interested in the one diode for fan 5 had no passage. I then soldered the diode with a relatively large amount of solder Bypassed. Now fan 5 is recognized. With fan 4 this has unfortunately not works ;-)
- 36GB DDR3 Registered ECC RAM
- NoName 32GB SD card for VMWare ESXi
- HP Proliant DL360 Gen5 (Used as a shelf for the " Lackrack". Too loud and too much power consumption)
- 1x Intel Xeon Unknown
- 32GB DDR2 Registered ECC Ram
- Raspberry Pi 4 4GB
- 128GB SanDisk Ultra MicroSD card for OpenMediaVault
- Old 500GB HGST 2.5" HDD
- Netgear ReadyNAS Duo V1
- 2x 1TB WD Black (The NAS is Slow AF, about 11MB/s write)
- Fujitsu TX120 S3 (main server, "productive")
- Intel XEON E3-1220 V1
- IBM ServeRAID M5110
- 1x Samsung 860 EVO 500GB
- 1x Seagate ST2000LM0071R81 (From an external hard disk)
- WD Green 1TB (Works with the integrated S-ATA controller there 3,5"; is there anything difficult to get into the 2.5" bays)
- EdgeRouter X (Main Router, not directly in my lab... but on the other side of the room), ISP 1Gbit/s DOWN, 50Mbit/s UP
Translated with www.DeepL.com/Translator (free version)
1
Right on the side of the bed? What about the noise? In the winter, just leave that radiator off and start mining some bitcoins to heat the bed :)
2
Its in the Livingroom and thats my Couch :D
4
If that side table is the same one I have, at least the server is providing structural support :P
1
Yes. I only use the dl360 (the grey one) and a shelf for the Dl380 (the black one)
1
Hi I got a question about this : Raspberry Pi 4 4GB - 128GB SanDisk Ultra MicroSD card for OpenMediaVault - Old 500GB HGST 2.5" HDD
What is the case reference for the hdd ? To you have issue about powering it via raspberry pi USB ports ?
1
No Problems so far. im using an Cheap USB 2.0 to S-ATA2 Adapter. Runs since a week
1
How do you like that printer? Looking to get it soon
1
Its quite good. Got it 4 free from work
1
What do you use it for? Print server?
-1
The Printer has its own Printserver. Currently doing MCSA 2016
1
Nice setup, are you planning on using that radiator anytime soon? Might get a tad toasty
The radiator only serves decorative purposes.
[deleted]