Help me upgrade S2 brakes

Question

Hi everyone. I'm awaiting my S2 and I'm already catastrophizing, because that's what I do, and I already know I want to significantly upgrade the stock brakes. I'm approx 190 lbs, and I'll be hauling a sidecar and kid totalling about 75 more pounds around hills with traffic stops, bike paths, etc. I'm looking at Magura MT5e or eStop and MDR-P rotors, but I'm confused as to differences, what I need, and how much is overkill.

Can you help me understand what I need for a full front and back replacement, while keeping motor cutout and brake light functionality? Is 220mm up front and 203mm back ridiculous? Just right? IDK, please help me, Super Squad, and thank you!

Posted Nov 15, 2020, 11:10 PM UTC · edited

316
Super73UK•

With 3 batteries, sometimes 2 adult riders and more modifications that any other 73 bike we have ever seen, our bike is very, very heavy (unlike the S2 our S1 also has a steel frame which is heavier).

We run 203mm rotors front & rear with hydraulic callipers and have more than enough stopping power, our rotors have never warped and are still going strong.

If anyone tells you that 203mm rotors warp then they are either referring to poor quality, cheaply made rotors and/or they don't know how to set the brakes up correctly so the brakes then overheat and damage the rotors.

If you buy a decent set of 203mm rotors, set them up correctly and brake correctly then you will not have a problem.

It's better to have too much braking power than not enough braking power - If your bikes braking capability is too weak then you will have to work the brakes hard and this will cause them to overheat so fit the best brakes you can get!

We would suggest getting 180mm to 203mm adaptor brackets for front & rear and then fitting 203mm rotors to both front & rear. This is most likely all you will need to do to give you enough braking power.

This video may be of interest to you as they discuss the size of the rear rotor and make some good points:

https://www.youtube.com/watch?v=ieeV3pLSoVo&feature=emb_logo

​

(We are not an official UK dealer & have no affiliation in any way to "Super73" the bike company)

3
GoMonkey66OP•

Thanks for that...the video got me thinking. I guess it makes sense from a motorcycle standpoint to have that big rotor up front, but it is weird to think that ONLY approximately 30% of your braking force is in the back, because I feel like I mostly rely on my rear brake, but maybe that's my MTB brain not wanting to go over the bars face first.

When it comes to the mass of the S2/rider/sidecar/child/"stuff" I should feel pretty confident in 203mm front and rear for mild hills, right?

I don't see any downside to bigger rotors aside from mass - you'll have better effciency, cooling, fade resistance, etc., but not necessarily stopping power, right? I mean, that's the calipers and pads doing that work...I can see why on a motorcycle or downhill MTB that a huge rotor up front would be desirable, but for S2 purposes 203/303 should not be a problem?

2
Super73UK•

203mm front & rear will be plenty if you have them set up correctly.

Bigger rotors will also give you better stopping power compared to smaller rotors if the smaller rotors overheat under load.

It is worth getting a good quality set of 203mm rotors - We upgraded our S1 160mm stock rotors for 203mm front & rear and have only one regret - That we didn't do it sooner!!

This may be of interest to you:

https://www.reddit.com/r/Super_73_Mods_Plus/comments/hp2hua/difference_between_160mm_203mm_brake_discrotor/

1
watchbuzz•

Rotors aside... a simple upgrade would be the pads. The bikes come with the A10.11 tektro pads they seem to be finicky. Make sure to bed them properly. I couldn’t seem to get them right and upgraded to the high performance P20.11 tektro pads and have found them to be way better. Better and more even stopping. Less noise. No turkey gobble.

2
GoMonkey66OP•

Great point, upgrading pads and then rotors should be simple enough for anyone, regardless of know-how, to do and would be a nice performance increase. Stock are 180mm Tektro...any pad recommendations?

1
watchbuzz•

I have the tektro performance P20.11 pads and like them.

1
GoMonkey66OP•

Thanks, just ordered a set. Since the bike will be brand new I'll just put them on first and bed them and keep the stock ones as emergency spares, thanks.

(Edit: sorry...you mentioned the pads in your first post...somehow my brain skipped that, lol)

1
watchbuzz•

😎👍

1
AutoModeratorMOD•

Hey u/GoMonkey66,

If you happen to not receive a response on here, be sure to join our Discord server!

There may be some members on there that can quickly answer your questions!

https://bit.ly/RS73-Discord

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

1
MarcusMeadPK•

Highjacking this post a little, would live to get the Magura MT5e for my S1 is that possible? Just wondering if the connectors would work or not so i can keep the Break lights working

1
GoMonkey66OP•

Yep, you just need the levers with the Higo connectors, and you'll have motor cutoff and brake lights.

1
MarcusMeadPK•

Oh sweet is it just a straight plug and play swap? That would save so many headaches lol

1
GoMonkey66OP•

I haven't done it myself on these, but I've swapped and adjusted plenty of levers before, and it's not hard at all. Keep in mind you'll need to deal with brake lines and hydraulic fluid, so make sure you're comfortable with bleeding the brakes.

1
MarcusMeadPK•

Yeah hydrolics are fine i was just mainly worried about the ebike connectors tbh. But if they just plug and play then ill be getting them for sure

1
norkerone:R_Green:•

Don’t go up to 203. Those rotors provide a good bite but warp and their lifespan can be very short.

If you really need 203 only do the front one, and leave the back at 180. Maguras are amazing, if you end up upgrading just buy two complete break sets from them.

It will be plenty of stopping power.

0