Possibly Bad Idea: Ryobi One+ Dildo
imgur.com/a/KUUcXhgPosted Nov 22, 2020, 9:10 AM UTC
Posted Nov 22, 2020, 9:10 AM UTC
I just don't get it
Agreed. I'm familiar with electric wheelchairs, and electric massagers, but not electric wheelchair massagers.
I think it's a sybian, basically? But honestly why use batteries at all, when DC supplies are so readily available? And if it's a sybian, there are DIY plans for that where you don't have to muck about with eccentric masses.
I'd much rather use an offset pin on a drive wheel with linkage and constraints vs. an eccentric rotating mass, for anything with "stroke" to it.
Can you tell me more about these offset pins on a drive wheel with linkage and constraints?
I'm not sure if you're genuinely interested in what I mean, or if you thought you were calling me out for my pretty ugly word jumble haha. looks like you're using SolidWorks for fusion 360, so I figured I'd use terms you're familiar with.
The offset pins would be a such distance from center on a drive hub connected to a motor. These pins would link an arm to the wheel. The arm is would have to be constrained in the axis of motion at the opposite ends to convert the radial motion to linear.
Changing the offset of the pins, relative from center of the drive hub, results in two times longer stroke than distance the pin moved, because radius vs. diameter.
I think everything here is pretty straightforward I think, except for the blue area which a "u joint" or "cv joint" style knuckle union.
This is what most thrusting machines use for converting radial to linear motion, because you can't really get much more simple than this.
Agreed, and I'd rather use a stepper motor per the Kinky Makers plans than an offset cam ;)
Just not sure what OP is going for here. But interested to find out!
I can't think of any reason other than possibly torque to use a stepper motor in place of a standard hobby servo? You don't need 1.8° increment resolution on a cam offset haha, and even if you did, a simple gearing would address that. But I guess stepper motors and stepper motor controllers are cheap enough.
Long story short, this is my prototype plan for a vibrating dildo powered by 18v Ryobi One+ power tool batteries. Vibration is provided by a quite powerful electric wheelchair massager motor. I've drawn up the basic design in CAD, as the majority of the housing is going to be 3d printed. The 18v batteries will be "bucked" down to ~12v to avoid exploding the massager motor, and I plan on using a potentiometer in the circuit to allow the user to control speed. The issue that is giving me pause at this point, is that just the housing is going to be roughly 13 inches long not counting the toy itself. Not sure if I should go forward with this due to the ridiculous size. There will, of course, be significant waterproofing measures taken up to the battery linkage. Any ideas or comments?
13 inches is 33.02 cm
Unsure what direction you want the vibration movement to go - in/out, or eccentric about the base? If "about the base" is good enough, you could cut up one of the bigger, more powerful computer fans;
- chop off all the blades
- bust the motor out of the frame
- sand everything nice and smooth
- glue a concentric weight to one side of the hub (flat metal bent in a curve?)
- connect the stationary part of the motor to the suction cup end of the dildo
- keep your hands away from the spinning part, or make a guard for it...
Many fans can be had with speed control input on one of the wires. Some work with a DC level, even though PWM control was intended. 12V will be needed.
Anyway, that'll be a lot shorter in total length than a different design. I imagine a lot quieter too.
I have a Delta EHE fan that would take your finger clean off - it's rated at almost 4A - so it could be quite powerful, depends on the fan. I've no idea what the right / best fan to use would be - as this is not my original idea. FWIW,
Eccentric about the base should be sufficient. I’ll give this fan idea a try before I pull the trigger, I do want it to have a power range from “gentle tickle” to “magnitude 10”. Thank you!
You're welcome. Be warned that you really want to make sure any weight you add to unbalance the motor (with all the fan blades shaved off) is glued on very securely. I see many thousands RPM on some of these - should the weight let go, it could injure someone coming off at such speed.
I mention it after reading another using an unbalanced computer fan for a vibrator.
There, they just clipped a blade - kept the motor / housing part intact - which is probably a lot safer than what I suggested, albeit a bit "cooler". I'd certainly test it at full power maybe with a steel bucket over it first. Perhaps that "Goop" glue would be strong enough for a flat, curved hunk of metal - I just dont want to see anyone get hurt over an idea I brought to the DIY table.