Best jack/jack stand for a first time buyer?

Looking for a Jack and Jackstands for my 01 Camry to do the occasional oil change and use very, very rarely. I'm kinda looking for something that is 'just good enough' until I have the money to get something nicer, but not cheap Chinese steel to where it'll be damaged easily. Can anyone make any recommendations? Obviously I'm looking for something made here in the US if possible. I'm not averse - fully - to BIFL Over-kill stuff if I can use it forever, and I'll spend the extra money if I should. I'm wondering whether I should, I guess. Thoughts?

Posted Jan 12, 2021, 2:47 AM UTC

113
AutoModeratorMOD•

Thanks for posting on r/MechanicAdvice! This is just a reminder to review the rules. If you are here asking about a second opinion (ie "Is the shop trying to fleece me?"), please read through CJM8515's post on the subject. and remember rule 3a, please post the year/make/model of the vehicle you are working on. If this post is about bodywork, accident damage, paint, dent/ding, questions it belongs in r/AutoBody or r/Diyautobody If you have tire questions, check out r/howsmytire and ask there. If you dont have a question and you're just showing off it belongs in r/Justrolledintotheshop This is an automated reply

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

1
vectorvitaleOP•

Side note - how often do y'all actually change your oil and transmission fluid? When do you do a full "flush"?

1
Shadow_Guy01•

I just use whatever jack stands I got at oriellys 10 years ago. Change oil every 5k or whatever your manual says. Tyranny fluid every 30-40k miles

To change oil -

Unscrew the screw on drain pan, wait for it to stop then put the screw back in.

Unscrew oil filter, and replace. Note to put some oil on the little rubber bit, and only hand tighten it.

Add oil, done.

Basically same thing on a trans, but you gotta drop the while pan (like 15 bolts) and then try to not get all messy. Then change the flat thingy sticking in the bottom of the transmission. That's the filter. Add fluids, done.

1
vectorvitaleOP•

Thanks so much!

I'm going to my local garage soon to do a full transmission flush, where they clean out the whole shebang (it has 132k and I have no record of the last change), is there any way, based on the info about the engine, to know whether there are other filters or things I should get done when I do that? It's a 01 Solara V6.

Edit: doing some light searching has shown me that apparently doing a full flush is for heathens and should be outlawed, and that I should do a drain and fill instead.

2
ShoutingMatch•

I use plastic ramps.

1
MM800•

Rhino Ramps, and Horrible Freight jack stands. Both have served me well for many years.

2001 F250 diesel 4×4 - bought it new. Four gallon oil and filter change @ 5,000 miles - Shell Rotella 15W-40. Transmission drop pan, filter and fluid every 30,000 miles (the transmission is the weak link on this truck). Coolant drain and fill every 4 years. Replace brake fluid every 3 years. Draw out and replenish power steering reservoir twice a year. Front and rear differential + transfer case fluid replacement, every 50,000 miles. Replace fuel and air filters every 10,000 miles. The truck is 20 years old. Original engine, original transmission, original axles and transfer case, original radiator, heater core, transmission cooler, power steering cooler. Things I have replaced: Water pump - last year, one fuel injector, one fuel pump, one axle seal, batteries, tires, brakes, serpentine belt twice with new idler and tensioner pulleys.

2009 Hyundai Elantra, 11 years old, bought it new. Oil and filter change @ 3,000 miles - Mobile1 synthetic oil. Transmission fluid and filter change every 30,000 miles. Brake fluid every 3 years. Cabin and and engine air filters annually. Coolant drain and fill every 3 years. Timing belt replaced at 85,000 miles with new tensioner pulley. Engine mount, serpentine belt, tensioner, idler pulleys, and spark plugs, replaced when I did the timing belt. Brakes, batteries, and tires, replaced struts and shocks last year, one window regulator, and the drivers side sun visor. In 11 years, that is all that has ever been replaced on this car.

On your Camry: use only genuine Toyota coolant and transmission fluid, that is specific to your car. Don't follow the Toyota maintenance intervals - do everything early. 3,000 - 4,000 synthetic oil changes, your coolant and brake fluid are due now, your transmission no more than 50,000 miles. Or you can do like most people and face big repair bills.

1
vectorvitaleOP•

Thanks so much for your reply!

I mentioned above - when I do the transmission fluid (I guess drain and fill?) how should I go about doing that? I'm reading everything and universally everyone is saying a full flush isn't recommended, and to instead do (possibly multiple) drain and fills over a period of some months? Do you agree with that?

1
MM800•

I agree with that completely. Flushing machines can be detrimental to transmissions. If you drop the pan and wipe it out, install a new genuine Toyota filter, and use genuine Toyota fluid, every 30,000 - 50,000 miles, you'll be good. I do my vehicles at 30,000 miles, because it's cheap insurance against replacing the transmission.

1
vectorvitaleOP•

Thanks so much! I'm going to have my mechanic do it this time, and see if he will let me watch him so I can do it myself the next time.

Can I buy genuine transmission fluid for a reasonable price online? Does it have to be Toyota branded or can I buy anything with that 'DEXRON' type? Same with the filter, you mention 'genuine toyota', is there really gonna be a difference between that and, say, a "Wix" branded one I get at oreilly?

1
MM800•

On those items, stick with genuine Toyota. Rockauto.com often has the genuine OEM parts for less money.

1
MM800•

The reason I laid it out the way I did is; I have 2 old vehicles, and neither has had a major repair. The truck went 19 years before it needed a water pump. Why? Because I used genuine Ford coolant, and I replaced it before its corrosion inhibitors had depleted. No oil leaks on either vehicle. Why? Because I changed the oil before it got enough 20 micron particles suspended in it, to do any seal damage. You will learn - right now the most important thing to learn is; don't follow automotive "snake oil" gimics, follow the successful.

Never let your tank drop below 1/8, and study "Top Tier" gasoline.

1
fakeaccount113•

if you wanted something made in USA you will probably end up spending 800 bucks on a jack and 2 stands. Not sure who even makes that in USA, maybe snap-on? Not worth it. I have harbor freights more expensive daytona yellow floor jack and its better than anything the dealership I used to work at ever provided. It releases easily and most importantly it goes down slowly and its easy to open the valve up just a tiny bit and control the speed. I have harbor frieghts aluminum 3 ton jack stands - they were only a little bit more money and I leave them outside a lot. I left my suburban on them almost 2 years.

1