Can anyone tell me what this rattle noise is? I'm thinking it's a throwout bearing. In the video, it happens as the car is turned off, sort of blocked out by the beep. Sorry for the crappy video, context is in a comment.

Question

Posted Jan 29, 2021, 11:16 PM UTC

13
JakeyAtWorkOP•

Again sorry the crappy video, I didn't know how else to film it myself, and also sorry for the wall of text that is this comment. I figured I'd give detailed context.

I bought a 2013 2.0T with 87k+ miles on it, now at 91.5k. This is my first manual car, so I could just be paranoid at the different sounds, but I'd rather be safe than sorry. I have a couple ideas of what it is, but I'm not entirely sure.

  1. I'm pretty sure it's the throwout bearing.
  2. Possibly rod bearing, though I don't think so.

The rattle in the video happens when the car is turned off, but it is muffled a little bit by the beep. It always rattles when turned off. It is relatively quiet, and it sounds like it's from the engine bay or below at the trans.

I also hear the rattle blended in with the engine noise when I rev it from idle, specifically coming down roughly around 2k rpms.

I also hear it quietly at low speeds changing gears, for example, approaching a stop sign in a mid or low 2nd gear, coast and slow to a stop pushing in clutch (rattles quietly here) to avoid stalling and to put it in 1st as I check for traffic and start accelerating again.

I only find it possible for the rattle to be a rod bearing because the noise itself sounds like the noise the Sonata made prior to entering a limp mode and eventually blowing the engine (I told the fools several times what it was, they didn't listen, it died, and they dropped a new long block and internals in for free because they refused to listen to me). I generally don't think it's this because it was much louder, and always on revs starting at 2500 and above, on or off load. This is quieter, only on revs coming down in neutral, or when disconnecting clutch. It could be happening otherwise, but it's not noticeable to me.

If it is a throwout bearing, how much would that set me back for a new clutch and throwout installed. I have a general understanding of it all and learn very easily, how hard would it be for me to replace this myself without a car lift? If you've made it this far down, thank you a ton for reading!

1
Buddahz•

Can’t really tell from the video bud. It’s way to short before you opened the door and the beep overtook All sounds. If the clutch and flywheel is aftermarket you will hear a rattle. Now if it’s stock and if it is the slave cylinder(these come one piece and you won’t find it under the name throwout bearing you will find the part under slave cylinder when looking for replacement, how do I know? Cause I just did my clutch swap about 3 weeks ago and my slave cylinder was replaced as well) the job itself isn’t horrendous but a second pair of muscle helps to lift the transmission much easier unless you have a trans jack. The job can take from 6-8hrs or a day or two depending how mechanically inclined you are. YouTube has lots of videos on this process that’s how I did mines. All the way thru no issues. A clutch kit can be anywhere from 600-1000 maybe including the slave. Hope it helps some bud. Good luck

2
JakeyAtWorkOP•

Thanks! Sorry, I cut the video because I was idling before shutting off, and the rattle on shutoff really only happens for a second or two as the engine dies. Damn beep really overpowers, I'd turn it off or whatever if I didn't have other things to worry about first.

I'm assuming it's stock since the rest of the car is, but I don't know for a fact. Maybe they burned the clutch and had it replaced with an aftermarket, just speculation. I could probably handle it, and I'd definitely have help from a friend or two. My main struggle would just be figuring out the best way to get under the car safely, I'll definitely need to buy some stands. I think it'll be okay for now at least while it's quiet. Thanks for the help!

1