OMTech 60w - Make It Fit

This community has been pivotal in helping me get more laser for my money. THANK YOU!

I really like the Boss 16-14 and it is all I really need, but for thousands less, I can get more machine to grow into in an OMTech 60w.

The Rub:

The Orion won't go where I want it to unless it can partially be disassembled to get it through 32" door.

Anybody know if this is possible?

Posted Mar 8, 2021, 12:55 AM UTC

316
Dave01a•

That is a definite maybe.

The stand does bolt to the main cabinet, but in mine, the assembly guys also put every screw for the Z lift mech and motor through the bottom of the main cabinet and into the stand frame. So that's like a dozen and a half little screws. So I can separate mine, it just takes more than four or six bolts.

I would get it, but plan on adding a couple of layers of plywood between them and swapping machine screws for short lag screws. Then when you do move it back out, it will literally only be the stand screws.

2
ChristOP•

Thank you!

1
ChristOP•

After re-reading this, I understand and that is great advice.

1
Dave01a•

Mine made it in the shed door by inches. I took a close look to see what was involved. From the outside you only see the stand bolts, no big deal. It was the first time I had the inside bottom cover off for cleaning that I noticed the jack screws, idlers, and drive motor mount all screwed down into the stand frame.

If that's what you have it's more time the first time than anything. Only other thing I could think you might need would be longer screws / bolts up through the plywood to the main cabinet.Ideally, some good thin layer 1" plywood would be the best solution, but I seriously doubt the home store is going to carry it.

2
kaminm•

The OMTech Facebook group has some information on where the screws are located so that you can remove the base from the cutter itself.

They had this video posted in their announcements area: https://www.youtube.com/watch?v=mch3PdnvORw

2
ChristOP•

This video is so insanely helpful. Thank you!

1
ICollectHobbies12•

https://www.ebay.com/ipp/264944180017?transactionId=2726932183016&_trksid=p2047675.l48352

Key point - Package Size 49“L x 34“W x 31.5“H(124 x 86 x 80CM)

The crate fit EXACTLY through a 32" door. I thought I was going to have to take the door off the hinges or take the laser out of the crate to get it inside.

​

Dan

1
ChristOP•

I should have been more specific. Looking at the 20 x 28.

1
BananaTurd•

Highly recommend not getting the autolift or autofocus. Neither are necessary and the autofocus actually makes it more complicated when changing lens tubes. It takes me literally 5 seconds to focus manually, and it’s one less thing to break.

Also, to your original question, the 20x28 blue/gray (what I have) will absolutely disassemble from the base with 4 bolts. Then you just flip it on it’s side and it’ll easily fit through any door.

2
ChristOP•

Interesting.

I expect to have many hundreds of an object of two different heights with some random height objects thrown in for engraving.

If manual focus is so easy...

Do you know if the auto focus is something that operates mid burn in order to handle irregularly shaped objects? A tapered form?

I don’t plan on changing out lenses or tubes very often.

1
BananaTurd•

Regardless of whether you’re using manual or autofocus, the z-height is fixed for the entire burn of a file. Autofocus doesn’t move throughout the project and see where you have different variations in material (that won’t work anyway with a fixed laser head), it just moves down and senses where your material is, and then backs up from there to the optimal height. It actually takes longer than doing it manually, and many times the autofocus can be wrong if the settings aren’t right.

If you have irregularly shaped objects, you’re likely going to have to segment the work of each cut and focus separately for each height difference. Otherwise you’d have to set the focus based on the highest point (so the laser head doesn’t run into the rest of the project) and then any low cuts would be out of focus.

Not sure if this is making sense or not, but I think the main point is autofocus doesn’t really add a ton of value, and unless you’re going back and forth between 1/8” wood and large objects requiring a rotary tool, you’re probably not going to be making massive movements of the bed height. Even if you are, you can just turn the belts of the manual bed with your hand and it moves quickly.

Let me know if that makes sense.

1
ICollectHobbies12•

Good luck, they just update their lineup and the dimensions were flat-out impossible (The shipping size was smaller than the machine size in all 3 dimensions). This has been corrected but I'm not sure how much I would trust them.

1