r/Coffee•
micro18

V60 Filter placement/rinsing

Hey, how do you make you filters snuggly fit with the brewer ? I found that if I do not correct it after the rinse, the filter is not fitting the V60 close enough and it affects the brewing time significantly. Any tips ?

Posted Mar 24, 2021, 1:26 PM UTC

016
mz68Pour-Over•

I don't think they're supposed to sit "snuggly" unless I'm misunderstanding this somehow.

4
micro18OP•

Why would it ? The cone is shaped with fins so the close fit ensures that they work as intended ?

0
mz68Pour-Over•

No they are there to prevent the filter from sticking to the walls. If it stuck firmly to all sides it might mess with the drawdown.

The "brewer" really doesn't do that much, the brew process happens inside the paper filter.

4
WinterMelonToufu•

What do you mean buy “snuggly fit”.

If you are talking about having the wet filter paper to be adhering to the v60’s walls. Then that is exactly opposed to what it is meant to be. The spines along the brewer is made so to prevent the paper from sticking to allow the water to drawdown faster.

If you are talking about the paper somehow not aligning to the cone, maybe youre using the wrong size paper for the brewer? There are 3 sizes (as i know of) for v60 paper by Hario.

3
micro18OP•

Well, except it draws slower when not fit close to the brewer. Anyhow, just looking for some opinions on the matter.

1
mz68Pour-Over•

Don't see how it could drain slower that way tbh. The problem has to be something else.

3
micro18OP•

May be, won’t argue about that.

1
toomuchinfonowSiphon•

After making it as round as possible, I rinse by pouring in the middle to weigh it down and then spiral upward so it adheres to the sides.

3
micro18OP•

This is somewhat so had in mind today. Weighing it down in the middle first and go round up. Will try this next time.

1
DJRFG•

That is what I've always done as well. (Although that doesn't guarantee it is correct). I'm surprised it makes much difference, I would have thought adding the grounds and then water during the brew would weigh the filter down enough to accomplish the same thing anyway.

As others have said the point of the ribs on the brewer wall is to stop a seal forming causing an air lock (as can happen with the Chemex). However provided there is not a perfect seal, increasing the path for air would make a minimal difference.

An explanation for why your drawdown is quicker when the filter is making more contact with the brewer walls could be an increase in the capillary effect due to the extra pressure from the brewer walls on the paper. (This is why a wet tent can leak when you poke it). That effect would increase the amount of bypass you get (water flowing down outside the paper) resulting in a quicker drawdown.

1
vk_9•

Fold at the rim, place it inside the v60. hold it with one hand while pouring a little water with the other just to get the filter settled in. After that, take out the hand and continue rinsing.

2
micro18OP•

Been doing it like that for a long time but recently noticed that if I push it a little down, the fit is a LOT better. Just curious about other’s findings.

1
vk_9•

I found the same thing when I first started using hario filters. But it was very inconsistent for me, so I stopped fidgeting with it and let it settle in naturally. Curious to see if anyone else has better ideas!

2
friendnoodle•

If the fit's weird, your mountain fold may need some tweaking. Try folding it farther past the crimp. (New Hario filters aren't as consistent in construction as the original ones were.)

2
DJRFG•

That would effect the angle of the paper.

1
lokemon_35•

Apply downward pressure slightly as you rinse the filter. That'll do the trick if you want a better fit

2