Bottle conditioning problem

This morning I went down to check on my bottles that are conditioning in my fermentation chamber and noticed one of the bottles had a little foam in it. I realised the cap on it was slightly askew so decided to open and replace it properly, but when I did a torrent of foam was released and went everywhere. I was a bit worried all my bottles would now be over carbonated but when I tried opening one of the 500ml bottles there was only a small fizz. So I am wondering did I do something wrong when bottling? Why did the one bottle foam up like crazy?

The beer is a weissbier, was fermented at 17c with an FG of 1.008 read twice 3 days apart. I bottled almost 13 litres of it using 100g dextrose monohydtate to try reach about 3 vol of CO2. When prepping the sugar I added it to 100g water and boiled for 10 mins, then added to the bottling bucket before siphoning the beer on top. I siphoned a bit too much beer so got some extra sediment and yeast but decided I didn't mind since I don't mind a little sediment/yeasty taste. I then bottled into 24x500ml and 3x330ml bottles, all swing top, I did the 500ml ones first and the 330ml last. This is only my second beer so I am a bit worried, any help is appreciated.

edit: Forgot to mention this is only after 36 hours of conditioning

Posted Apr 3, 2021, 8:15 AM UTC · edited

315
dingledorfer2•

Looks like you primed with just under 1 oz./gal. , so you shouldn't have a problem with over carbonation. I'd suspect you either didn't get a good mixing of the priming sugar or the bottle you opened had some sort of contamination.

5
scrib_blezOP•

Guess I'll hope it was just a case of not mixing the sugar in properly as opposed to a contamination. What can I do to properly mix the next time?

1
jagnew78•

I second u/dingledorfer2 that you probably didn't get a good mix on your sugar water and some bottles are overcarbonated. The amount of priming sugar you put it was definately not too much.

Next time when you siphon your beer into your bottling bucket, after all the beer is in stick in the big stir stick/spoon and slowly, and gently stir the beer to make sure you get a homogenous mix of your sugars into your beer. You just want to try to reduce the amount of oxygen stirring can potentially introduce.

I had uneven bottle conditioning on my second batch. This is my third batch just finished and everything seems great this time around and I did this exact thing. I stirred for about 45 seconds or so slowly and then transferred to bottles.

EDIT: Just to add to this chill all your bottles for several hours before you open them. That will help reduce the amount of potential foaming your going to get if you have any further overcarbed bottles. And, open them in the sink to be safe.

Also if you have flip top bottles, or twist off caps to a light bottle burp with the flip top or just a slow twist with the cap. That should release just a bit of the carbon and you can gauge whether or not you've got an overcarbed bottle in your hands

5
scrib_blezOP•

Thank you, I'm definitely going to focus on mixing the sugars in properly in the future, hopefully that will help avoid a problem like this again. Why does this happen when chilling? Does it just force some co2 out of solution or something? Sorry for all the questions just curious

2
schlagers•

Chilling helps keep CO2 in solution because gasses are more soluble in liquids at lower temps. Foaming is CO2 rapidly coming out of solution because of the drop in pressure after you open the bottle.

2
dingledorfer2•

When I bottled the uneven carbonation problems I experienced were minor. I have heard brewers report major problems too. I found that a gentle stirring, concentrating on going from bottom to top, after adding beer to the priming solution and again after every dozen or so bottles gave me even carbonation.

3
scrib_blezOP•

Ok I'll have to try focus on mixing it in carefully and properly the next time to be sure. Thanks for the help. I forgot to say that this is only after 36 hours of conditioning, would this point more towards a contamination since it is such a short amount of time?

1
nah-meh-stay•

My bottling process is to rack the beer onto the priming solution in the bottling bucket. I use a racking cane upside down in the bucket with the bend against the side of the bucket to create a whirlpool as it racks. By the time I get everything set up for bottling, it's mixed well.

3
crispydukes•

I didn’t check your math, but g do not open warm bottles.

If you’re worried, chill it for 24 hours and check.

2
scrib_blezOP•

Thanks I'll keep that in mind

1
crispydukes•

If one bottle is good enough, then chill them all.

2
scrib_blezOP•

Forgot to mention this is only after 36 hours of conditioning, should I still chill them?

1
crispydukes•

Take one bottle and put it in the fridge for 24 hours. If the carbonation is perfect/high then chill them all ASAP.

If the carbonation is low/medium, give it another week and try again.

2
[deleted]•

[deleted]

1