I'm moving soon; can't figure out how to lay out my new workshop

I'm moving soon; can't figure out how to lay out my new workshop

Posted Apr 10, 2021, 12:27 AM UTC

820
rs_joe•

1st step, remove those space hogging cars!

20
WeaponizedNostalga•

Came here to say that

8
Nickover50•

Yep, the blue spaces have to go. Don’t even think about keeping the one spot thinking it will make your life easier, it won’t ...once wood dust hits her car you’re in for a whole world of pain never experienced. Keep her on the driveway and retain some dignity.

2
KalzenithOP•

I live in northern Canada, definitely keeping my cars in the garage

0†
OutWithTheNew•

My one car stays on the street all summer. Shop gets shutdown by Thanksgiving and the car goes back in. Consider putting all that you can on casters and doing the same would be my advice.

I'm not scraping my windshield if I can avoid it.

Unless you actually have a wall, you're just going to cover the cars in sawdust.

2
[deleted]•

Then put everything on heavy-duty lockable caster wheels.

4
AutoModeratorMOD•

Reminder: Comments not related to woodworking will be removed. Violations to rule 1 including crude jokes, innuendo, sexist remarks, politics, or hate speech may result in an immediate ban

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

1
KalzenithOP•

My new place has a 3 car garage, the third spot will become my dedicated woodworking shop. This is an upgrade from everything being crammed against the side of a 2 car garage

Ideally, I want to have the bandsaw, planer, and miter saw each have infeed and outfeed space, but I'm having a hard time figuring out how to make it work without the need for rolling carts or flip carts

The bandsaw is the tool that gets the most use in my shop, so I want to give it preferential treatment, but I can't figure out how to integrate it into this layout

There is going to be a floor-to-ceiling tarp separating this shop from the rest of the garage

Does anyone have any tips for optimizing tool layouts to eliminate shuffling them around to use them?

1
Unwieldygoose•

Is there power along that partition?

1
KalzenithOP•

The partition doesn't exist, I plan on hanging tarps there to mitigate dust on the car side

I'll most likely be stringing extensions over there

I thought about putting the planer and miter saw on the left wall, but the miter saw would need to jut out pretty far forward because of the sliding rails that extend out behind the saw

1
burritosandbeer•

You're a woodworker. Look into framing a bit and you'll have it sorted. I believe in you

1
KalzenithOP•

Definitely a possibility, we'll need to re-evaluate when I actually move in

1
burritosandbeer•

Fair enough. Good luck my man

2
lumieres-de-vie•
  • Is your planer (edit: it’s not a planet) freestanding, or is it sitting on your bench top? (I’m assuming all the brown is the top of the bench.)
  • Could you put the bandsaw at the bottom end (below the miter saw on the diagram)? It could share feeding space with the miter?
  • Where do you have materials (wood) storage in your diagram?

Personally, when I’ve laid out workspaces, I find it the most helpful to think about where the wood is getting stacked between steps. (For example, raw material through the jointer, then through the planer, then table saw, then miter saw, then router table before hitting the assembly station.) If you mark all the places where the pieces get stacked between steps, you’ll have a good idea of the flow of the workspace and the layout usually falls into place from there.

1
KalzenithOP•

It's a 12" Lunchbox planer. My plan was to recess it into the bench top so it's flush with the bench surface. Same with the miter saw

I could put the band saw on the end, but then there would be no infeed room unless I open the garage door and move the bench to the left by a few feet. And the bandsaw blade might get in the way of the miter saw outfeed

I haven't actually figured out lumber storage yet.. there's space for long term drying storage outside, but not sure where I'll keep sheet goods, cutoffs, and dimensioned lumber yet

1
MrSpark7•

Get a car lift and 2x the shop.

1
dryeraseboard8•

This could be great, but also maybe too big? https://youtu.be/DzmVpFmqvvw

1
joegard15•

Not sure what kind of woodworking you plan to do, but I set up my original shop similar with workbench mounted along the walls. What I found is that I often wanted to be on the other side of my work piece when assembling and finishing. You might think about a workbench that you can pull away from the wall as necessary so you can walk all the way around the work.

1
KalzenithOP•

most of my woodworking is small to medium sized furniture pieces. coffee tables, raised dog bowls, dog beds.. stuff in that size range.. I'm also getting into woodturning

maybe some U-shaped surfaces would be more efficient

https://i.imgur.com/ceitUnV.png

1
745632198•

I'd put the miter station against the wall. You don't want dust and wood chips flying all over your vehicles.

1