Printing with ABS on the Ender 3 v2?

I'm attempting to print the Voron M4 extruder in ABS to replace the factory extruder on my Ender 3 v2, and it's been difficult to get passable prints.

Using Hatchbox Black ABS, I'm having issues with corners curling up from the bed even with increased bed temperature.

The best attempt thus far was without a draft shield and turning on the part cooling fan at 20% after the first few layers, but there's still some warping - enough that I don't feel the part is usable.

The hotend is at 235C and the bed is maxed out at 110C - I haven't been able to get the ABS to stick well at lower temps, so it's possible bed adhesion is a part of my problem.

Could I alleviate this with an ABS slurry (or other adhesion aid), or will I need to enclose the printer?

EDIT:

I found a solution (even if it were not optimal), so I feel obligated to share what worked for me.

Hatchbox Black ABS:
245C extruder
110C bed temp
cardboard to partially surround the printer as a draft guard 12mm brim (overkill)
Draft Shields
Printing at 40mm/s.

The Black ABS actually adhered very strongly when it stuck, the problem was it often didn't, even with what I felt was a proper bed level. After the first layer went down it was pretty easy to tell when a print would turn out.

I used Esun ABS+ for the accent parts and I found it was much harder to work with. The adhesion wasn't anywhere near as good.

Posted Apr 12, 2021, 2:31 AM UTC · edited

38
EidolonVS•

Just going to leave this here...

https://www.thingiverse.com/thing:2637437

3
TopHATTwaffle•

Are you printing with an enclosure? They are essentially required for ABS.

2
MariaKonopnicka•

On glass - glue stick, heat bed to 60 and cool down to under 30C. Apply ABS slurry on top. Works really well. Prints release easily below 40C.

1
HeadShotzOG•

I had the same issues you have with abs but now i have no issue with warpinf and i dont use any adhesion to stick it to my glass bed and the only thing that solved my problem is printing in enclosure

1
derpinator12000•

I have done it on an ender 3 pro with an upgraded hotend. 235 is a bit cold for abs but going higher on the stock direct bowden hotend is a really bad idea.

For adhesion you need a wide brim and probably need to re-level the bed at temperature (my bed moved a lot between 60 and 110C). You can also somewhat cheese it by turning up the flow for the first layer. Worked for me on a clean glas bed.

Also absolutely do use a draft shield and NO FAN, not even for bridges (make sure your min layer time is high enough).

If that fails you could try asa, it's a bit easier to print on an open frame.

1
Error400BadRequestOP•

I have done it on an ender 3 pro with an upgraded hotend. 235 is a bit cold for abs but going higher on the stock direct bowden hotend is a really bad idea.

I have a capricorn PTFE tube installed and it is rated for use up to 260C, so I could bump the temperature if need be. I also have a new hotend on the way, but I'm still waiting for it to be delivered.

Regardless, I was running at 235 because the recommended temperature range on the spool was 205-240, but if you feel higher temperatures should work better, I'm happy to try.

For adhesion you need a wide brim and probably need to re-level the bed at temperature (my bed moved a lot between 60 and 110C). You can also somewhat cheese it by turning up the flow for the first layer. Worked for me on a clean glas bed.

Okay, I'll give this a shot later today. Is there anything else you feel I should keep in mind?

1
derpinator12000•

I have a capricorn PTFE tube installed and it is rated for use up to 260C

That is 260c real temperature, not 260c set on printer temperature, not that the stock firmware would let you much higher. Seriously though don't mess around overheating ptfe the stuff it puts out is really bad (like kill birds and make you very sick bad).

My abs profile is 280c but that's just what works best with the particular spool i have, generally prints do get stronger with more temp up to a point where it falls of a cliff.

In your case I'd try brim, draftshield and no fan first and then start turning up the temperature. Also let the bed heat soak for a bit before you level or start printing, thermal expansion is a bitch and the thermistor is on the bottom.

1
Smith532•

Are you using Cura as your slicer? If you are try enabling "Draft Shield" under Experimental. It puts a wall around your part that helps to keep it from warping. They say it works well with ABS. You'll find some tutorials on Youtube.

I'm waiting for my Hatchbox Black ABS and will probably get it Wednesday. I'd be interested in what you come up with. It will be my first time using ABS also.

1