Cannot setup Z-wave JS with HUSBZB-1

I have a fresh install of HASS OS 5.13, supervisor 2021.03.9, core-2021.4.3 on a raspberry pi 4. I've easily gotten "Zigbee Home Automation" configured with the HUSBZB-1 and have some lights working with it. However, I cannot get the new "Z-wave JS" to configured with the USB stick.

Method: Click on "add integration", select "Z-wave JS", click submit with "JS supervisor add-on" checked. Paste my USB device path "/dev/serial/by-id/usb-Silicon_Labs_HubZ_Smart_Home_Controller_C1300913-if00-port0", leave network key blank, and click submit. After I click submit I immediately get "Aborted. Failed to set Z-Wave JS configuration." In addition to the serial by id path, I've also attempted the dev-path "/dev/ttyUSB0". All documentation indicates USB0 or if00 is the z-wave port on the stick and I confirmed by checking my zigbee setup which is USB1 or if01.

​

Verification of path: To verify the path, I later attempted setting up Z-wave (depreciated), using path "/dev/serial/by-id/usb-Silicon_Labs_HubZ_Smart_Home_Controller_C1300913-if00-port0" which is successful with no issue.

​

Any ideas what else to try? Perhaps is the HUSBZB-1 not supported by Z-wave JS?

Posted Apr 12, 2021, 4:46 AM UTC

44
1980techguyOP•

Solution:

Every time I tried to add a new Z-wave JS integration it would fail. However I found under Supervisor > Dashboard there was an icon for Z-wave JS. I selected that.

Then I selected the "configuration" tab at the top, then I was able to select my z-wave device path of "/dev/serial/by-id/usb-Silicon_Labs_HubZ_Smart_Home_Controller_C1300913-if00-port0" which was pre-populated in the dropdown.

After saving that, I went back to the info tab and started the service. (I also selected "start on boot", "watchdog", and "auto update".

Once that was running I was able to go back to the integration window and add the Z-wave JS supervisor add on successfully, this time it auto identified the device.

After the add-on is installed I was able to go into "configure" and use the "add node" to successfully add devices.

​

Thanks to all for your suggestions.

5
zippyruddy•

It definitely works...I'm using it with that stick via a separate docker container and it has been working really well. Sorry I can't give you any advice on how to get it going through Home Assistant since I don't use it that way, but I can tell you it does work.

2
booradleysghost•

Did you ever experience a problem with adding nodes? I'm using the same setup in docker and zwavejs2mqtt sees the HUSBZB-1 stick, but I can't get it to add any nodes, inclusion always ends with no changes found.

1
CallMeDrewvy•

I've got it running just fine with that stick and Zwave JS. I am using the ZwaveJS2mqtt addon instead, but just because it has a nicer interface.

I use the /dev/ttyUSB0 path, but I also have a network key. Try adding a network key since that's needed for secure zwave devices.

2
booradleysghost•

Did you ever experience a problem with adding nodes? I'm using the same setup in docker and zwavejs2mqtt sees the HUSBZB-1 stick, but I can't get it to add any nodes, inclusion always ends with no changes found.

2
CallMeDrewvy•

Tbh I haven't added any zwave devices since I switched to zwavejs. My network carried over from the previous config.

1
booradleysghost•

Thanks for responding. I did end up getting it to work with a lot of rebooting and persistence.

1
xtrawork•

I couldn't get it either. I finally just edited my configuration.yaml file and that seemed to work...

Also, while I could get the Zigbee HA integration to configure, I couldn't get it to see my Zigbee devices. The only way I fixed it was to go into Configuration.yaml and put in the config lines in there as well.

Every other integration I've configured since has worked and I haven't had to edit that config file anymore, but those two integrations just wouldn't work without it.

EDIT: I just noticed in my log file that ZHA is complaining about me using those lines in the config file, saying that it's deprecated and I should remove them. Problem is, if I do, ZHA won't see any of my Zigbee devices, so I am not really sure what to do except leave it in there until it stops allowing that line in there...

1