r/synthdiy•
UKtwo

Help with silent audio jack

I recently purchased a noise synth that came as a DIY kit. I have it built and everything is sounding good, however it has two 3.5mm audio outputs and one of them (the primary output unfortunately) is silent. I tried running it through a guitar amp and was able to get faint audio that sounded fine other than being barely audible. As this is my first real delve into circuitry of any kind, I'm wondering what could be causing this problem? I figure the jack itself must be broken since the rest of the synth seems to function fine, I'm just a bit confused since it seems to still be capable of producing a faint signal when amplified. Thanks to anyone who is able to guide me toward fixing this issue as it's been somewhat of a let down for me thus far.

Posted Jun 10, 2021, 8:55 AM UTC

110
Ghosttalker96•

If it's an issue with the audio jack, check the connection:

Plug in a cable, check continuity. The tip should be connected to the signal output, the ring/base should be connected to ground.

3
UKtwoOP•

How do I check for continuity? Sorry I'm very new to this stuff.

1
Ghosttalker96•

Use a multimeter. Set it either to resistance measurement or to continuity mode, if the multimeter has one. Either you measure a very low resistance (a few ohms) or continuity is indicated by a beep.

1
littlegreenalienSkullAndCircuits•

Get out your troubleshooting hat... and hammer. But better get a multimeter and a scope. Builds that don't work properly at first try are pretty normal. I've build a dozen or so Metal-o-trons and none worked fine at first power up. I know the circuit well since I designed it, but somehow I always screw up in some way.

So firstly, take out your magnifying glass and check all your soldering. If something even looks a bit dodgy, reflow it (heat it up again). Also check for unintentional bridges between soldering islands.

Secondly, did you place all components and did you place them correctly? Especially resistors. Check them. Also check polarity on everything and especially check the orientation of the IC's. Don't trust the IC socket, see that pin-1 is correctly in regard to the PCB. You might have soldered the IC socket the other way around (It happens)

90% of the time, the 2 steps above will fix things.

The other 10% is harder to debug and need some insight in the schematics. Measure throughout the circuit until you can find the place where things go wrong. It helps if you know how the circuit works so you can assess correctly what kind of signal one should see and why you don't.

It's not uncommon for IC's to be faulty. Especially if you bought them from some shady cheap chinese ali-express shop. But even trustworthy suppliers will ship out the odd faulty component. Last build I did I had a diode that was not working. It happens.

2
UKtwoOP•

All of my solders appear good, except for one where two pins of a chip holder have blobbed together. I don't have the correct tools to fix this, but the synth sounds totally fine from the second output, it's just that the second output bypasses a filter, so I can't get the filtered audio without audio from the main output. All of the components should be of good quality, as the kit came from a reputable distributor. Everything seems to work other than the main audio jack which can only be heard when cranked through an amplifier. Unfortunately this is my first venture with circuitry of any kind, so diagnosing even with a schematic would be extremely difficult for me. The components are all in their correct spots though, and polarity has been accounted for.

1

take your soldering iron and try to reflow and spread that blobbed part that is jumping connections. heat up the blob and try to pull away/ make space between them. if you have some spare wire or alligator clips you can try to wire up a makeshift jackless output before the jack itself. adhere the two wires/clips to your cable and to the joints where the audio jack is soldered in- bypassing the jack itself

1
GypsumFantastic25•

Which noise synth kit?

Can we see a schematic?

1
UKtwoOP•

It's the Chernobylizer by Isn'tses. I don't have a schematic, just a basic instruction manual that tells where each component goes on the board, but there are photos of the synth on their etsy page that show all of the components on the board from multiple angles. The output jack in question is the one on the top left of the board.

1
GypsumFantastic25•

Hmm it's really hard to troubleshoot without a schematic, and it's hard to see the tracks through the fanciness of the PCB.

Just check the basics - have you got all the components in the right places and (if polarised) the right way round? Are your solder joints good? If you have an oscilloscope, how far does the signal get?

It'd be a bit unusual for a jack plug component itself to be defective like that - they're so simple inside. Not impossible though I suppose.

2
professorbiohazard•

I've had similar problems when building guitar pedals and diy modules. In most of them it came down to a cold solder joint and just identifying which one it is and reflowing the joint fixed it. but once it was a bad capacitor. This was in a big muff clone. Had voltage going into the cap, but none coming out. Same symptoms you describe. It sounded great, just super quiet with volume maxed. Replaced the cap and everything worked.

1