Power wheels Jeep Upgrade questions

Got a free Power Wheels Jeep, no idea what works and what doesn't. Waiting on parts.

Here is current plan:

2x 20v(18v) Dewalt Battery holders wired in parallel.

1x Low voltage protector (or should I use one per battery)

1x Automotive relay feeding a adjustable voltage regulator

​

I would then like to add an RC kit as my daughter is to young to drive herself right now. But I heard that sending 18v through these 12v kits will kill them pretty fast. This is the kit I bought:

https://www.amazon.com/gp/product/B079X4F9DW/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1

I guess I could always keep the voltage regulator at 12v until she is able to drive herself and I could just eliminate the "brain" part of the RC kit. I can handle all the wiring and fabrication. Just don't want to accidentally fry something. Not looking to go crazy fast. It also sounds like I should not supply more than 12v to the steering module.

Any other tips?

Posted Jan 27, 2022, 6:15 PM UTC

315
BaconJacobs•

The power to the motors should run through the relay and the relay should be shut on and off by the Low Voltage Cutout. That way you're not running any high amperage through the LVC.

5
On_To_Better•

Yes to this! That little board will fry with the full load

3
brooksytechOP•

Yes, that is the way I am going to wire it. TY.

2
Subliminalme•

IMO, I'd skip the 2 battery setup and just do a single battery setup and have the kid switch them out when done.

I had the same setup, but ended up just going with one.

4
Nouio•

The ride time essentially doubles if you have two batteries. If you want the increase in riding time without having to change the batteries, I'd recommend doing the upgrade. My ride time with a two battery setup is over 3 hours.

3
Subliminalme•

Oh, i understand...My setup is a few years old now and I've definitely had to replace some parts along the way...including the powerwheels...got a different one on the marketplace and swapped over the setup.

They're for kids...they can keep an extra battery sitting in the battery compartment and simply swap it out when the first one dies. Little more work for the kids, a little less electronics to go wrong.

I dunno...you can go either way...just in my experience, less is more here. :)

2
treyendo•

Throw an inline 15 amp fuse between battery and regulator, cheap and easy to replace. I fried a board before realizing… I run one 12 AH m18 it’ll go all day

3
brooksytechOP•

Yep, will definitely use a fuse there. Thanks.

1
Nouio•

You can feed more than 12v to the steering motor. Mine has held up with 18v-20v for about 50 hours and I don't see there being any issues in the future. Because the motor is used so rarely, it won't heat up too much.

You do not want to send more than 12v through that harness you bought. It will fry the controller instantly. Don't try to convert the ~18v to 12v with a voltage converter that has a dial on it. All it takes is one accidental increase and the board will fry. Use 24v to 12v converter units that only have ports for wires. Something like this.

You will want a 24v wiring harness. Like this.

The wires are a higher gauge and copper. All of the fittings seem to be done better than the stock 12v wiring harness that I got.

Make sure you use the switches and buttons that come with the harness, many of the 12v buttons will fry with more volts fed through them.

I've learned these lessons through my mistakes, not by someone's word online.

1
gabe801•

I’m a total noob to this stuff but could I still use the converter you linked with my m18 batteries?

Basically can I use that 24v to 12v converter or should I get a 18v to 12v converter? Like this one?

1
Nouio•

Man no worries. You are asking the right questions. I didn't know any of this before the build either. This was a fun, and valuable learning experience for me.

You can put any voltage below 24v in and it will be rounded down to 12v.

1
gabe801•

Thanks I appreciate the help! I wasn’t planning on switching to 18v so soon as we just got the power wheels second hand last week. Battery turned out to be bad so instead of replacing with a stock one I figured just switch to 18v but try and preserve the stock motors for a little while longer so I’ll be stepping it down to 12v for now!

1
paparandy61•

Place an on off switch in the line to the low voltage protector, otherwise the low voltage protector will always be “on” potentially draining the battery.

1
brooksytechOP•

Yep, I bought a 30a switch to do just that. Thanks.

1
GreaseMonkeyRayJay•

Does someone have a wiring diagram with the relay?

1