PC Wall Mount : Need expert opinion, will this schematic plan work?

Question
PC Wall Mount : Need expert opinion, will this schematic plan work?

Posted Jan 31, 2022, 6:41 AM UTC

1K117
DivinerUnhinged:windows: Ascending Peasant•

I’m confused, are you actually mounting your PC parts on the wall like this? What’s the purpose of the fans?

438
dalopyonOP•

The fan is just decoration, since i already have it might as well haha. Also its the only part that i can stretch longer further from the mobo and psu, need the whole frame to be this long (1500mm) because the wall itself is quite long as well (3500mm)

165
DivinerUnhinged:windows: Ascending Peasant•

Oh so this is kind of an art project too. Gotcha.

119
TAOJeff•

As the fans are just for decoration, if you have an issue with weight, you can split it into 3 frames, you can add a couple of dead HDD to the fans on the left, center one is the PC, right hand one with the last fans and the camera. It would also take up a bit more wall space.

21
SatinAcornfredd•

I need new fans 😭

1
Kratosferico7700K | Nvidia 1080ti SLI | 32gb 3600MHz•

I see what looks like cable holes, so I think it is some kind of desk pc, but hanging on the wall.

124
dartsshroomboom•

I think he’s going to put it all in a glass box like case and then mount that to the wall edit so it’s more like a pc case mounted to the wall

2
vivek7593•

It can work, but here few pointers to look out for -

  1. AIO needs atleast 4-5 inches of gap on both sides to effectively work ( draw and expell air ) . If you arent leaving that kinda space then try mounting it with fans facing down. And not against wall. Or else go for beefy tower cooler.

  2. Cable routing for peripherals and see if length of these cables suffice. Also try to place the hardware on flat surface to mimic your placement and see whether the psu cables are in reach.

  3. Usb c or 3.0 Extension hub if you frequently use external hdds or other stuff.

  4. If its gonna be open wall mount , then it gonna be a bitch to keep it clean , so having air purifiers might help .. only if you leave dusty area.

142
dalopyonOP•

Truly appreciated the feedback,

  1. Yes i was trying to not making custom mount for the AIO haha, but as of now the gap behind the board is only 1.5 inch, so likely i’m gonna need to do as per your suggestion
  2. Luckily cabling wise i have lots of extender and some gpu and mobo strimer, as of now on flat lay the cable dont have much problem, but i still need to observe further once i have the backboard and the cables went behind.
  3. Same for the USB’s luckily i have some hub extension, although most of my peripherals doesnt work as smooth if not plugged in directly. This frame pc will be mounted on the wall on top of my monitor so most of the tabletop stuff will be ok, but i will have problem with the short main power cable.
  4. Air purifier is a good suggestion! honestly i didnt even know that those thing reducing dust. There’s no window in this room so the dust should be as minimal as it can possibly be (i hope)
43
vivek7593•

For PSU power cable , you can get cables with extra length.. attaching link PSU 5 meter power cable

Or else connectors like these however would prefer single of cable instead of having connectors in between.

Power cable extender

7
dalopyonOP•

I went with something like the first picture (around 3m) hopefully it perform as expected

5
peperonipyza12700K | 3070 Ti FE | 32GB 3600Mhz•

There’s always dust, best to plan for a way to clean it out when it builds up.

5
bustedbuddhaPC2•

What about putting the AIO on 'legs' so it was a few inches 'above' the backboard towards the viewer?

2
edgeofblade2•

Not to make fun of you… it’s great to learn something new every day and we celebrate those moments… but what did you think an air purifier did if not remove dust from the air? There are some that ionize the air and that has a mild odor removal effect (at the expense of creating more ozone at ground level). Sometimes those purifiers make claims about “toxins”, but the main thing they do is remove dust, because so much just travels on the “dust” itself.

2
dalopyonOP•

I never own or use an air purifier before, i really thought its only function to remove some damp smell or other odor. TIL

2
edgeofblade2•

Eh. Some people use them religiously to remove “toxins” from the air, but they really just circulate air and filter particles like dust or pollen.

2
Lachesis577•

I had nearly the same build (after a year i changed to a full custom loop), swap the AIO fans with the radiator (so they blow to the front and u just see the radiator), I have 4,5cm behind my build and no heat problems. Its easier to pull air from near the wall then to push it against the wall (and quieter too)

1
dalopyonOP•

Yep it was also in the plan, was trying to avoid that because need to do custom mounting for the radiator haha

1
Lachesis577•

I printed all my mounts, maybe u know someone with a 3D-printer

1
111111911111•

I have an open PC mount as well. I blow out the radiator every 6 months or so, but there's not much in it. I live in a house that's probably messier than the average home, so I'd expect yours to be fine as well.

1
Perrozoso•

Why is there a random ass camera?

49
dalopyonOP•

Good question, the camera (X70) is to complete the theme of the setup, black white silver aesthetics and mounted on “photo frame”, also similar form factor of rectangle and round.
The camera mount is also one of the steel plate that gonna support the frame.

34
Perrozoso•

Nice very artistic and unique.

I don't think your AIO will work very well against a solid surface. I think you need airflow to move through it. Would suggest designing some sort of air intake from behind.

I don't think a PSU can mount like that out of the box.

Nice power button.

Edit: your GPU will be pushing heat vertically downward which isn't physically optimal.

8
dalopyonOP•

There’s actually gonna be cutout hole on most of the parts, and some gap behind the board, with some ventilation on top, some of the mounting method will be as close as possible as how we mount it on pc case, but for some parts like the gpu gonna need to make custom mount to hold the thing properly haha.

The GPU heat direction is gonna be one i need to think further yes, can only be done once i get the riser cable and see where all the air going

2
HotcakeNinja:steam: GTX 1050 Ti // Ryzen 3 1200•

Retrofitted into a webcam obv.

1
voidspaceistrippyCats are cool•

This isn't going to look as good as you're expecting it to.

  1. Get the components.
  2. Actually line up the real life components
  3. Base the cosmetics around the actual product dimensions.
9
dalopyonOP•

The components already have it, well most of it, still waiting for the gpu riser cable and strimer, and the schematic is to scale to actual product dimensions, i’ve tried to flat lay the components on to scale paper, And you are right, aesthetically speaking its obviously looks messier, especially on 45 degree angle haha. I hope it will look neater once the backboard done and the cables are tucked inside

3
voidspaceistrippyCats are cool•

Probably :D <3 Just remember to get a cable wrap or something to manage the cables going to & from it.

2
dalopyonOP•

Hello there PCMR, inspired by all the nice wall mounted pc pictures, i’m planning to mount my parts into a custom wood frame (with gap space behind to hide the cables).
The thing is i have very limited experience in building pc, i have only built exactly once and that with some help.
So this will be very exciting for me since i’ve never done this before, luckily i have some knowledge in CAD and construction, so the structure part is roughly settled.
I foresee my problem is more on the hardware parts itself, for example i might not be able to place the GPU that way like in the schematic above due to the extender riser length or direction.

Feel free to chip in if you foresee any problem, before i actually start cutting the wood frames, back structure to hang etc haha. any advice is appreciated. Take me as a total noob in pc building because i actually am.

6
BatmanWantsToBeMe•

I'm thinking about the radiator. You present it into the push configuration with fans on top. As per other comments in the thread it might be an issue do to little space behind the board. So perhaps you could consider using pull configuration with fans on the bottom? This would give you different look (was the fans would be between the backboard and the radiator, so bare radiator would be showing) but would also give you better thermals...

1
smallgreenman•

Something to keep I mind (I speak from experience) if you're using white agglomerated wood you should raise your gpu a bit because agglo insulates quite well and will just keep the metal backplate of your gpu warm. You should also know that it's very hard to get a clean looking cable run if it isn't either straight or bending at a 90° angle.

1
Kedarnok•
  1. Why fans if U want aio?
  2. Why aio at all?
  3. Will U do some cover for it also? So it won’t get all dusty in few days?
  4. Do U have all of the pc parts now or not yet? And what parts these are?
5
dalopyonOP•

1 and 2. the AIO is to distribute the overall weight and to make it less protruding out

  1. Wont have any cover, because glass cover this size is very heavy. Yes it will be dusty haha

  2. Most parts i already have, its mostly NZXT, and other than that its Gigabyte Vision GPU, the fan on left and right is just for aesthetic.

3
rokdoktaur•

The more I look at this, the more I want one.

5
axeleliteintuition•

As long all the circuits are connected and electrons are flowing, you can put a pc in your anus and it will still work. I can't see any reasons why it wouldn't work if all the wires are connected. Make sure you have adequate air flow

5
hammerampage•

Looks awesome

4

i swear some of u mfs has too much free time. Cool idea tho

4
dalopyonOP•

Thanks to WFH and pandemic i guess, saves me money and time at the cost of minor depression.

4
I_am_nova696969i7 2600k, rx 480, 16gb ram•

If you pull it off this will look amazing and I would love to see it

4
pedrito009•

DIWhy?

3†
TheAcest•

I like what ur going with! The concerns I can think of seem to have already been voiced, the radiator intake etc. Perhaps if the radiator had a little mount that would raise it up a bit it atleast wouldn't suffocate, don't know if thats optimal tho. Best of luck! ^-^

3
dalopyonOP•

I hope it will work too! There will be cutout hole on every part, the board will either be plywood cut with CNC or laser cut acrylic panel. But as others have pointed out, the gap behind the board (around 1.5 inch) might not be sufficient for the airflow, then i need to mount it to different direction which i’m gonna have problem with weight distribution haha, its gonna be lots of trial and error for this one.

2
TheAcest•

Ah right, sounds a lot of effort haha but well worth it in the end im sure. Hope to see the end result high on the sub.

2
WoooshToTheMax:windows: R5-3600 + 5700xt•

Why do you just have 4 random fans?

3
Quirky_m8•

#dust

3
Tilowo•

GPU should be in pcie slot #1

3
TheSarcasticClam•

I actually want to see this light up and work.

2
q-ka•

I’d probably suggest you actually get the parts and workshop a layout IRL

2
breakzyx•

you might wanna go for a top down aircooler instead. if not make sure your aio is properly spaced from the wall so air can actually go through. if mounting in concrete there are special heavy weight dowels i would use. good luck

2
Architechno141•

I only want to say that the only thing I'm worried about is the riser cable being long enough to go under the gpu and loop around to connect to it.

2
dalopyonOP•

It likely wont be long enough to do that, i can only figure it out once the riser cable come, its one of the most important component before i can go to the next stage of cutting the board.

1