BeFlatLineOPT1D (1990) - Dexcom G6 / OmniPod Dash (AndroidAPS Closed Loop)•

Previously, I was using multiple daily injections (Basalgar and Novolog). On 11/30/2021, I started on OmniPod Dash because I knew that OmniPod 5 was on the horizon and how game changing looping could be. In January, I found out that AndroidAPS was working on a DIY closed loop system using the OmniPod Dash - so I began the steps to try that. The timeline goes:

  • 11/30/21 - First day of pumping with OmniPod Dash
  • 1/23/22 - First day of trying AndroidAPS - in an open loop status.
  • 2/5/22 - Began closing the loop - starting in "Low Glucose Suspend" mode.
  • 2/6/22 - Fully closed the loop while gradually lowering my BG targets.
  • 2/9/22 - Loop is fully closed and now have 2 days in a row of 100% time in range (70 - 180 mg/dl)

AndroidAPS released 3.0 recently, which unlocked the ability to loop using your own phone with the OmniPod Dash. It takes a lot of work and tweaking to get setup, but if done carefully and with proper safety precautions it can be life altering.

I am really excited for OmniPod 5 also. This took a lot of work to setup and it wasn't easy. A commercially available product will have formal training from educators, which will make closed loop systems more viable and accessible to the wider community. That's truly game changing. We're living in amazing times.

8
jbr7rr•

Good to hear! I'm currently wearing the demo pod, was diagnosed first week of this year. Looking also for looping, already running androidAPS in open loop mode (still on MDI though). Hoping to get the real pods in about a month or maybe two (have to get approved by insurance etc)

Do you have connection issues with the pod? If you day a lot of work, do you mean for the dash specificly or to setup androidAPS and looping in general?

Also which CGM do you use? And do you use the androidAPS bolus wizard or SMB?

Edit: NVM the CGM, see you're using the dexcom, I'm on the libre2 (xdrip+/oop2)

3
BeFlatLineOPT1D (1990) - Dexcom G6 / OmniPod Dash (AndroidAPS Closed Loop)•

No connection issues on the pod using a Samsung Galaxy S21 Ultra. For work, it was mainly fine tuning all the settings and making sure my ratios were spot on. In addition, reading up on how AndroidAPS works and doing the objectives to unlock full functionality. I am currently working on objective 8, so I'm nearing the end of the "work" needed to set it up. Due to this, I haven't unlocked SMBs yet - but will be using those in the future. I currently use the bolus wizard and try to frontload my insulin @ about 80% of what it says I'll need then let the loop figure the rest out. I do this since I'm not following a strict diet and have to estimate my carbs most of the time. I'm using Fiasp, so I also have to be careful on the timing because it starts to kick in after about 12 minutes for me.

Good news is that Omnipod 5 is being offered currently to some in the US (on a trial basis) and is slated for a full release in the near future. Omnipod 5 in theory should be easier to setup using the stock software that Insulet will provide and should be supported by trainers - so, if reading and experimenting a lot isn't your thing, there will be a lot of trained people to help you along the way.

Congratulations on taking the steps towards a healthier life! I know being diagnosed sucks - but the good news is that you have been diagnosed during a time where medical and technological advances has made diabetes a lot less of a burden than it was.

3
Sprig3•

I used SMBs for a bit, but found they would over-react for me when using some of my sites. I still use "unannounced meal mode", but I have the SMBs turned off.

Could be I have some settings wrong.

(I do turn SMBs back on when I use my legs for pods, though.)

2
BeFlatLineOPT1D (1990) - Dexcom G6 / OmniPod Dash (AndroidAPS Closed Loop)•

I've heard good things on SMBs and unannounced meals, so I'm hopeful for once that feature unlocks fully for me. You might want to check your DIA setting: I had mine at 5 hours and had issues with overcorrections. I kept thinking it was my ratios, but once I changed DIA to 5.5 hours everything fell in line perfectly. I've heard that 6+ hours works really well for others and it's really dependant on the individual + which insulin they are using.

2
jbr7rr•

Thank you for your response and kind words.

I'm from the Netherlands, here insurance/healthcare does not cover CGM, only FGM (there are some exemptions). So thats why i'm stuck with the Libre 2 (For me not a problem as i basically use it as a CGM :)). Due to this I do not expect availability of the closed loop omnipod system within a few years. Further more, insurance only covers one pump kit per 4 years.

But I like to tinker and not afraid of doing some coding, testing etc as I work as an embedded software engineer. So thats why DIY looping is a good solution for me.

I will start with novorapid as that is what I'm using in the pens. Considering using FIASP or lyumjev in the pomp though if the loop reacts to slow or does some funky things (novorapid has a long active time for me)

2
igaloly•

Thank you so much for sharing!

2